NEC NP60 NP40/50/60 UM - Page 25

To select a menu language, follow these steps - lamp replacement

Get NEC NP60 - XGA DLP Projector PDF manuals and user guides
UPC - 050927253782
View all NEC NP60 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

3. Projecting an Image (Basic Operation) Note on Startup screen (Menu Language Select screen) When you first turn on the projector, you will get the Startup menu. The menu gives you the opportunity to select the menu in one of the nine languages. To select a menu language, follow these steps: 1. Use the SELECT ▲ or ▼ button to select one of the nine languages from the menu. LAMP STATUS POWER FOCUS AUTO ADJ. SELECT SOURCE ON/STAND BY OFF ON POWER FOCUS PIC-MUTE PAGE UP MENU DOWN ENTER EXIT 2. Press the ENTER button to execute the selection. After this has been done, you can proceed to the menu operation. If you want, you can select the menu language later. (→ [Language] on page 41) LAMP STATUS POWER FOCUS AUTO ADJ. SELECT SOURCE ON/STAND BY OFF ON POWER FOCUS PIC-MUTE PAGE UP MENU DOWN ENTER EXIT NOTE: Immediately after turning on the projector, screen flicker may occur. This is normal. Wait 3 to 5 minutes until the lamp lighting is stabilized. When the [Lamp mode] is set to [Eco], the LAMP indicator will light green. If one of the following things happens, the projector will not turn on. • If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this condition the projector will not turn on to protect the internal system. If this happens, wait for the projector's internal components to cool down. • When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp. • If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute and then turn on the power. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
17
SOURCE
AUTO
ADJ.
ON/STAND BY
FOCUS
LAMP
STATUS
POWER
SELECT
SOURCE
AUTO
ADJ.
ON/STAND BY
FOCUS
LAMP
STATUS
POWER
SELECT
EXIT
MENU
UP
PAGE
OFF
POWER
ON
PIC-MUTE
DOWN
FOCUS
ENTER
3. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup menu. The menu gives you the opportunity to select
the menu in one of the nine languages.
To select a menu language, follow these steps:
1. Use the SELECT
▲
or
▼
button to select one of the
nine languages from the menu.
2. Press the ENTER button to execute the selection.
After this has been done, you can proceed to the menu op-
eration.
If you want, you can select the menu language later. (
→
[Lan-
guage] on page
41
)
NOTE: Immediately after turning on the projector, screen flicker may occur. This is normal. Wait 3 to 5 minutes until the lamp
lighting is stabilized.
When the [Lamp mode] is set to [Eco], the LAMP indicator will light green.
If one of the following things happens, the projector will not turn on.
• If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this
condition the projector will not turn on to protect the internal system. If this happens, wait for the projector's in-
ternal components to cool down.
• When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp.
• If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute
and then turn on the power.
ENTER
EXIT
MENU
UP
PAGE
OFF
POWER
ON
PIC-MUTE
DOWN
FOCUS