NEC PX-60XM5A 60XM5 tabletop stand UM - Page 2
Caution - specifications
View all NEC PX-60XM5A manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
Attaching Plasma Monitor to Stand 1 Remove the stand from its packaging carton. Remove the spacer and all included items and then remove the stand from its box. ¶ View of packaged items Securing brackets Monitor attachment screws Cable clampers Spacer 3 Fixing plasma monitor to stand. 1 While pulling the upper part of the plasma monitor towards your body, screw the monitor attachment screws (M6 × 50 mm) firmly into place (4 locations). 2 Once the plasma monitor has been attached, rock the monitor gently to make sure that there is no looseness and that the screws have been screwed tightly into place. 2 2 Attaching plasma monitor to stand. ¶ Make sure that the stand and plasma monitor are properly aligned together, and then place the plasma monitor onto the stand. ¶ When doing so, pick up the plasma monitor holding it on from both the right and left sides, and then fit the attachment holes at the bottom of the plasma monitor over the anchoring fittings of the stand. Plasma monitor Anchoring fittings When picking up the plasma monitor, hold it from the bottom and from the handles of the monitor. Monitor attachment screws 1 Caution Once the plasma monitor has been placed onto the stand, immediately insert the screws and tighten them to fix the monitor into place. Failing to tighten the screws could result in the monitor falling over, which might in turn result in bodily injury. Because the plasma monitor is heavy and has a high center of gravity, installation by one or two people is hazardous. Please employ three or more people during installation, being sure to hold the handle on the back as well as the lower portion of the monitor, while supporting its top and bottom. Note Avoid placing the plasma monitor in a location where it would be exposed to excessive amounts of dust, humidity, tobacco smoke, or smoke from frying oil, as doing so could result in dirt or grit to accumulate on the surface of the monitor, which might in turn result in a degradation of picture quality. Avoid placing the plasma monitor in a location where it would be exposed to direct sunlight or where lighting would fall directly upon the screen. If surrounding light falls directly upon the screen, it would make the screen appear bleached in color and result in a degradation of picture quality. Caution Securing the plasma monitor in place Attach the securing brackets and screws provided with the stand to the plasma monitor in the locations indicated in the accompanying diagram, and then use separate commercially available screws (eye screw) and wires or some other similar item of sufficient strength to secure the plasma monitor into place against a wall, pillar, or some other surface or otherwise use the holes located at the rear of the stand to fix the stand into place. (Note that these brackets and screws are not used when using a separately sold ceiling attachment unit or wall attachment unit.) Be sure to take care of the securing wires when moving the stand or plasma monitor. Note that the wires and screws needed to secure the plasma monitor against a wall or pillar or against the stand are not provided with the stand, and that the proper items must be purchased separately in accordance with the type of object or surface against which the monitor is to be secured. Securing brackets Separately purchased screws Preparing the cables Use the enclosed cable clampers to bind the cables. Caution Be very careful not to apply force to the bases of the cables. 1 Insert the cable clampers into the cable clamper mounting holes. Cable clampers Cable clamper mounting holes Opening a cable clamper If a cable clamper is closed too tight, press the button shown on the left and push the extremity of the cable clamper to loosen it. Button 2 Bundle the cables and place them on each cable clamper. Opening a cable clamper 3 Close each cable clamper, and then pull its extremity to make the cables immobile. Unlock here with a finger. Specifications Model : PX-61ST2U External dimensions : 1000 mm (W) x 222 mm (H) x 470 mm (D) (39.4 in. (W) x 8.7 in. (H) x 18.5 in. (D)) Weight : 14 kg (30.9 lbs) ¶ The specifications and/or design of this product may be subject to change at any time without prior notice. NEC and the NEC logo are registered trademarks of NEC Corporation. Printed in Japan / Imprimé au Japon