NEC SC40 MultiSync LCD SC40 SC46 User manual - Page 21

Setup

Get NEC SC40 - MultiSync - 40inch LCD Flat Panel Display PDF manuals and user guides
UPC - 805736022087
View all NEC SC40 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

English Please see installation on page 6 of this manual and follow all installation instructions. 1) Determine the installation location. CAUTION: Installing your LCD display must be done by a qualified technician. Contact your dealer for more information. CAUTION: MOVING OR INSTALLING THE LCD MONITOR MUST BE DONE BY TWO OR MORE PEOPLE. Failure to follow this caution may result in injury if the LCD monitor falls. CAUTION: Do not mount or operate the display upside down, face up, or face down. CAUTION: This LCD has a temperature sensor and cooling fan. If the LCD becomes too hot, the cooling fan will turn on automatically. If the LCD becomes overheated while the cooling fan is running, the "Caution" menu will appear. If the "Caution" menu appears, discontinue use and allow the unit to cool. Using the cooling fan will reduce the likelihood of early circuit failure and may help reduce image degradation and " image persistance". If the LCD is used in an enclosed area or if the LCD panel is covered with a protective screen, please check the inside temperature of the monitor by using the "HEAT STATUS" control in the OSD See page 29). If the temperature is higher than the normal operating temperature, please turn the cooling fan to ON within the FAN CONTROL menu within the OSD See page 29). IMPORTANT Lay the protective sheet, which was wrapped around the LCD monitor when it was packaged, beneath the LCD monitor so as not to scratch the panel. Setup 2) Install the remote control batteries. The remote control is powered by two 1.5V AA batteries. To install or replace batteries: A. Press and slide to open the cover. B. Align the batteries according to the (+) and (-) indications inside the case. C. Replace the cover. CAUTION: Incorrect usage of batteries can result in leaks or bursting. NEC recommends the following battery use: • Place "AA" size batteries matching the (+) and (-) signs on each battery to the (+) and (-) signs of the battery compartment. • Do not mix battery brands. • Do not combine new and old batteries. This can shorten battery life or cause liquid leakage of batteries. • Remove dead batteries immediately to prevent battery acid from leaking into the battery compartment. • Do not touch exposed battery acid, it may injure skin. NOTE: If you do not intend to use the Remote Control for a long period of time, remove the batteries. English-15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
English
English-15
Please see installation on page 6 of
this manual and follow all installation
instructions.
1) Determine the installation location.
CAUTION:
Installing your LCD display must be
done by a qualified technician. Contact your dealer for
more information.
CAUTION:
MOVING OR INSTALLING THE LCD
MONITOR MUST BE DONE BY TWO OR MORE
PEOPLE. Failure to follow this caution may result in
injury if the LCD monitor falls.
CAUTION:
Do not mount or operate the display
upside down, face up, or face down.
CAUTION:
°is LCD has a temperature sensor
and cooling fan. If the LCD becomes too hot, the
cooling fan will turn on automatically. If the LCD
becomes overheated while the cooling fan is running,
the “Caution” menu will appear. If the “Caution”
menu appears, discontinue use and allow the unit to
cool. Using the cooling fan will reduce the likelihood
of early circuit failure and may help reduce image
degradation and " image persistance".
If the LCD is used in an enclosed area or if the LCD
panel is covered with a protective screen, please check
the inside temperature of the monitor by using the
“HEAT STATUS” control in the OSD
See page 29)
. If
the temperature is higher than the normal operating
temperature, please turn the cooling fan to ON within
the FAN CONTROL menu within the OSD
See page 29)
.
IMPORTANT
Lay the protective sheet, which was wrapped around the
LCD monitor when it was packaged, beneath the LCD
monitor so as not to scratch the panel.
2) Install the remote control batteries.
°e remote control is powered by two 1.5V AA
batteries. To install or replace batteries:
A.
Press and slide to open the cover.
B.
Align the batteries according to the (+)
and (–) indications inside the case.
C.
Replace the cover.
CAUTION:
Incorrect usage of batteries can result
in leaks or bursting. NEC recommends the following
battery use:
Place “AA” size batteries matching the (+) and (-) signs
on each battery to the (+) and (-) signs of the battery
compartment.
Do not mix battery brands.
Do not combine new and old batteries. °is can shorten
battery life or cause liquid leakage of batteries.
Remove dead batteries immediately to prevent battery
acid from leaking into the battery compartment.
Do not touch exposed battery acid, it may injure skin.
NOTE:
If you do not intend to use the Remote Control for
a long period of time, remove the batteries.
•
•
•
•
•
Setup