NEC X554UNS User's Manual - Page 7
Installation, Mounting, Please note the following when mounting, on wall or ceiling, Orientation - video wall
View all NEC X554UNS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 7 highlights
Installation English This device cannot be used or installed without the Tabletop Stand or other mounting accessory for support. For proper installation it is strongly recommended to use a trained, NEC authorized service person. Failure to follow NEC standard mounting procedures could result in damage to the equipment or injury to the user or installer. Product warranty does not cover damage caused by improper installation. Failure to follow these recommendations could result in voiding the warranty. Mounting DO NOT mount the monitor yourself. Please ask dealer. For proper installation it is strongly recommended to use a trained, qualified technician. Please inspect the location where the unit is to be mounted. Mounting on wall or ceiling is the customer's responsibility. Not all walls or ceilings are capable of supporting the weight of the unit. Product warranty does not cover damage caused by improper installation, remodelling, or natural disasters. Failure to comply with these recommendations could result in voiding the warranty. DO NOT block ventilated openings with mounting accessories or other accessories. For NEC Qualified Personnel: To ensure safe installation, use two or more brackets to mount the unit. Mount the unit to at least two points on the installation location. Please note the following when mounting on wall or ceiling • When using mounting accessories other than those that are NEC approved, they must comply with the VESAcompatible (FDMlv1) mounting method. • NEC recommends mounting interfaces that comply with UL1678 standard in North America. • X464UN/X464UNV: NEC strongly recommends Unit No gap Mounting Bracket using size M6 screws (10-12 mm + thickness of bracket and washer in under 8.5 mm No thread 4 mm Washers Screw length). If using screws longer than 10-12 mm, 10-12 mm (X464UN/X464UNV) 10-14 mm (X554UN/X554UNS) check the depth of the hole. (Recommended Fasten Force: Thickness of bracket and washers 470 - 635N•cm). Bracket hole should be under 8.5 mm. • X554UN/X554UNS: NEC strongly recommends using size M6 screws (10-14 mm + thickness of bracket and washer in length). If using screws longer than 10-14 mm, check the depth of the hole. (Recommended Fasten Force: 470 - 635N•cm). Bracket hole should be under 8.5 mm. • Prior to mounting, inspect the installation location to insure that it is strong enough to support the weight of the unit so that the unit will be safe from harm. • Refer to the instructions included with the mounting equipment for detailed information. • Make sure there is no gap between the monitor and the bracket. • When used in a video wall configuration for a longer time, slight expansion of the displays may happen due to temperature changes. Due to this it is recommended that a one millimeter gap is kept between adjacent display edges. Orientation • When using the display in the portrait position, the monitor should be rotated clockwise so that the left side is moved to the top, right side is moved to the bottom. This will allow for proper ventilation and will extend the lifetime of the monitor. Improper ventilation may shorten the lifetime of the monitor. Mounting location • The ceiling and wall must be strong enough to support the monitor and mounting accessories. • DO NOT install in locations where a door or gate can hit the unit. • DO NOT install in areas where the unit will be subjected to strong vibrations and dust. • DO NOT install near where the main power supply enters the building. • Do not install in where people can easily grab and hang onto the unit or the mounting apparatus. • When mounting in a recessed area, as in a wall, leave at least 4 inches (100 mm) of space between the monitor and the wall for proper ventilation. • Allow adequate ventilation or provide air conditioning around the monitor, so that heat can properly dissipate away from the unit and mounting apparatus. Mounting on ceiling • Ensure that the ceiling is sturdy enough to support the weight of the unit and the mounting apparatus over time, against earthquakes, unexpected vibrations, and other external forces. • Be sure the unit is mounted to a solid structure within the ceiling, such as a support beam. Secure the monitor using bolts, spring lock washers, washer and nut. • DO NOT mount to areas that have no supporting internal structure. DO NOT use wood screws or anchor screws for mounting. DO NOT mount the unit to trim or to hanging fixtures. Maintenance • Periodically check for loose screws, gaps, distortions, or other problems that may occur with the mounting apparatus. If a problem is detected, please refer to qualified personnel for service. • Regularly check the mounting location for signs of damage or weakness that may occur over time. English-5