Netgear GS116 GS116 Installation Guide - Page 1
Netgear GS116 - ProSafe 16 Port Gigabit Desktop Switch Manual
UPC - 606449034998
View all Netgear GS116 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
)NSTALLATION'UIDE NETGEAR 16-port Gigabit Switch Model GS116 Estimated Time: 5-10 minutes Unpack the Box and Verify the Contents When you open the box, verify that you received everything. The package includes: • NETGEAR 16-port Gigabit Switch Model GS116 • AC power adapter • Wall-mounting screws • GS116 Installation Guide (this document) • Warranty/support information card If you do not have everything listed above, see the support information card for contact information. If you are missing the support information card, get contact information at http://www.NETGEAR.com in the Technical Support section. Prepare to Install the Switch Decide where you want to place the switch. Find a flat horizontal surface such as a table, desk or shelf. The switch comes with wall-mounting screws. You can use the screws if you want to hang the switch in an open space on a wall. Make sure the selected location is: • Not in direct sunlight or near a heater or heating vent. • Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on all sides of the switch. • Well ventilated (especially if it is in a closet). Also, you will need one Category 5 (Cat 5) Ethernet cable with RJ-45 connectors for each device you want to connect to the switch. Each Ethernet cable must be less than 328 feet (100 meters). Install the Switch and Connect the Other Devices 1. Place the switch on a flat surface or hook onto the screws. 2. For each device, insert one end of an Ethernet cable into the port in the device and insert the other end into one of the Ethernet ports on the switch. BPS'IGABIT3WITCH'3 072 /N,INK "OTH"LINK!CT -- !UTO 5PLINK ,/#!, - ).4%2.%4 6$#! /&& /. 3. Connect the power adapter cord into the back of the switch and then plug the adapter into a power source (such as a wall socket or power strip). The Power light should light up. Power 072 BPS'IGABIT3WITCH'3 /N,INK "OTH"LINK!CT -- !UTO 5PLINK 4. Check the LEDs to confirm that all connections are correct. LED Power RJ-45 ports Activity • On: 16-port Gigabit Switch has power. • Off: No power. • Right LED on: 10 Mbps connection to a powered device. • Left LED on: 100 Mbps connection to a powered device. • Both LEDs on: 1000 Mbps connection to a powered device. • Blink: Activity on this port. Troubleshooting Problem Action Power light is not lit The switch has no power. Make sure that: • The power cord is properly connected to the switch. • The power adapter is properly connected to a functioning power outlet. If it is in a power strip, make sure the power strip is turned on. If the socket is controlled by a light switch, make sure the switch is in the on position. • You are using the NETGEAR power adapter supplied with your switch. Port number light is There is a hardware connection problem. not lit for a connected • Make sure the cable connectors are securely plugged in at the device, or stays on switch and the device. continuously • Make sure the connected device is turned on. • If the Ethernet cable is connected to a NIC or other Ethernet adapter, make sure the card or adapter is installed correctly and is working. • Make sure the cable is less than 328 feet (100 meters). Technical Support Thank you for selecting NETGEAR products. After completing the Smart Wizard configuration assistant, locate the serial number on the bottom label of your product, and use it to register your product at http://www.NETGEAR.com/register. Registration on the website or over the phone is required before you can use our telephone support service. The phone numbers for worldwide regional customer support centers are on the Warranty and Support Information card that came with your product. Go to http://kbserver.netgear.com for product updates and Web support.