Netgear GS418TPP Installation Guide
Netgear GS418TPP Manual
 |
View all Netgear GS418TPP manuals
Add to My Manuals
Save this manual to your list of manuals |
Netgear GS418TPP manual content summary:
- Netgear GS418TPP | Installation Guide - Page 1
Installation ProSAFE 16-Port Gigabit Smart Managed Switch with PoE+ and 2 SFP Ports GS418TPP Package Contents • NETGEAR ProSAFE® Smart Managed Switch GS418TPP • Rubber footpads for tabletop installation • Wall mount • Rubber belts for mounting • Power cord locker • AC power cord (localized to - Netgear GS418TPP | Installation Guide - Page 2
, enter the password. The default password is password. 7. Click the Login button. The System Information page displays. 8. Configure the switch for your network. For information about switch configuration, see the user manual for your switch, which you can download from downloadcenter.netgear.com
-
1 -
2
 |
 |
Installation
ProSAFE 16-Port Gigabit Smart Managed Switch
with PoE+ and 2 SFP Ports
GS418TPP
Configure the Switch With a Static IP Address
Note:
If your network uses a DHCP server, this section does not apply
.
Go directly to
Connect the Switch to a Network
.
If you are using static IP addresses in your network, configure the switch IP
address before you connect the switch to a network.
1.
Configure a computer with a static IP address in the 192.168.0.x subnet.
2.
Plug the switch into a power outlet and connect your computer to the
switch using an Ethernet cable.
3.
Open a web browser and enter
192.168.0.239
in the address bar.
The default IP address of the switch is 192.168.0.239.
A login page displays.
4. Enter
password
for the password.
The System Information page displays.
5. Select
System > Management > IP Configuration
.
The IP Configuration page displays.
6. Select the
Static IP Address
radio button.
7.
Enter the static IP address, subnet mask, and default gateway IP address
that you want to assign to the switch.
8. Click the
Apply
button.
Your settings are saved.
Connect the Switch to a Network
1.
Connect PoE (or non-PoE) devices to the RJ-45 PoE network ports on the
switch front panel.
Use Category 5e (Cat 5e) Ethernet cables terminated with RJ-45
connectors to make 1-Gigabit connections.
2.
Connect an RJ-45 port or SFP port on the switch to a network that
includes a DHCP server.
If you use an SFP port, you must insert an SFP transceiver module that you
can purchase from NETGEAR.
3.
Power on the switch and wait two minutes.
Package Contents
•
NETGEAR ProSAFE
®
Smart Managed Switch GS418TPP
•
Rubber footpads for tabletop installation
•
Wall mount
•
Rubber belts for mounting
•
Power cord locker
•
AC power cord (localized to country of sale)
•
19-inch rack-mount kit for rack installation
•
Resource CD
Check the PoE Status
The switch can supply up to 30W PoE+ (IEEE 802.3at) to each port, with a
maximum PoE power budget of 240W across all active PoE+ ports.
The PoE Max LED indicates the status of the PoE budget on the switch:
•
Off
. Sufficient (more than 7W of) PoE power is available.
•
Solid amber
. Less than 7W of PoE power is available.
•
Blinking amber
. At least once during the previous two minutes, less than
7W of PoE power was available.
Configure the Switch
You can configure the switch either by using a computer’s web browser or by
installing the Smart Control Center Utility (see
Smart Control Center Utility
) on
your Windows-based computer.
Web Browser Access
1.
For initial configuration, open a web browser on a computer that is on the
same network and subnet as the switch and enter the switch’s IP address.
If you are unsure how to determine the IP address of the switch, you can
use the Smart Control Center Utility.
A login page displays.
2. Enter
password
for the password.
PoE access points
PoE VoIP phone
Switch
Network
Internet
Sample connections