Netgear GS724TPv2 Installation Guide
Netgear GS724TPv2 Manual
 |
View all Netgear GS724TPv2 manuals
Add to My Manuals
Save this manual to your list of manuals |
Netgear GS724TPv2 manual content summary:
- Netgear GS724TPv2 | Installation Guide - Page 1
Contents • NETGEAR ProSAFE® 24-Port Gigabit Smart Managed Switch GS724TPv2 • AC power cord (localized to country of sale) • Rubber footpads for tabletop installation • 19-inch rack-mount kit for rack installation • Resource CD • Installation guide Configure the Switch With a Static IP Address Note - Netgear GS724TPv2 | Installation Guide - Page 2
the user manual for your switch, which you can download from downloadcenter.netgear.com. 9. When you are finished with the configuration, return the computer's antivirus program and firewall to their usual settings. Troubleshooting Tips Here are some tips for correcting simple problems that might
-
1 -
2
 |
 |
Installation
ProSAFE 24-Port Gigabit Smart Managed Switch
With PoE+ and 2 SFP Ports
GS724TPv2
Configure the Switch With a Static IP Address
Note:
If your network uses a DHCP server, this section does not apply
.
Go directly to
Connect the Switch to a Network
.
If you are using static IP addresses in your network, configure the switch IP
address before you connect the switch to a network.
1.
Configure a computer with a static IP address in the 192.168.0.x subnet.
2.
Plug the switch into a power outlet and connect your computer to the
switch using an Ethernet cable.
3.
Open a web browser and enter
192.168.0.239
in the address bar.
The default IP address of the switch is 192.168.0.239.
A login page displays.
4. Enter
password
for the password.
The System Information page displays.
5. Select
System > Management > IP Configuration
.
The IP Configuration page displays.
6. Select the
Static IP Address
radio button.
7.
Enter the static IP address, subnet mask, and default gateway IP address
that you want to assign to the switch.
8. Click the
Apply
button.
Your settings are saved.
Connect the Switch to a Network
1.
Connect PoE (or non-PoE) devices to the RJ-45 PoE network ports on the
switch front panel.
Use Category 5e (Cat 5e) Ethernet cables terminated with RJ-45
connectors to make Gigabit connections.
2.
Connect an RJ-45 port or SFP port on the switch to a network that
includes a DHCP server.
Note:
In a small office or home office network, connect the switch to the
LAN port of a router that, in turn, is connected to an Internet modem.
If you use an SFP port, you must insert an SFP transceiver module, which is
available from NETGEAR.
Package Contents
•
NETGEAR ProSAFE
®
24-Port Gigabit Smart Managed Switch GS724TPv2
•
AC power cord (localized to country of sale)
•
Rubber footpads for tabletop installation
•
19-inch rack-mount kit for rack installation
•
Resource CD
•
Installation guide
3.
Power on the switch and wait two minutes.
Check the PoE Status
The switch can supply up to 30W PoE+ (IEEE 802.3at) to each port, with a
maximum PoE power budget of 190W across all active PoE+ ports.
The PoE Max LED indicates the status of the PoE budget on the switch:
•
Off
. Sufficient (more than 7W of) PoE power is available.
•
Solid amber
. Less than 7W of PoE power is available.
•
Blinking amber
. At least once during the previous two minutes, less than
7W of PoE power was available.
Configure the Switch
You can configure the switch either by using a computer’s web browser or by
installing the Smart Control Center Utility (see
Smart Control Center Utility
) on
your Windows-based computer.
Web Browser Access
1.
For initial configuration, open a web browser on a computer that is on the
same network and subnet as the switch and enter the switch’s IP address.
If you are unsure how to determine the IP address of the switch, you can
use the Smart Control Center Utility.
A login page displays.
2. Enter
password
for the password.
PoE access points
PoE VoIP phone
Switch
Network
Internet
Sample connections