Netgear RN3130 Rackmount Hardware Manual - Page 25

ReadyNAS OS 6.2 Software Manual, boot menu modes.

Get Netgear RN3130 PDF manuals and user guides View all Netgear RN3130 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

NETGEAR ReadyNAS OS 6 Rack-Mount Storage Systems • Test disk. Performs an offline full disk test. This process can take four hours or more, depending on the size of your disks. Any problems are reported in the system logs, which you can view using the local admin page. For more information about viewing the system logs, see the ReadyNAS OS 6.2 Software Manual.  To access the boot menu: 1. Power off your system. 2. Using a straightened paper clip, press and hold the Reset button on the control panel. 3. Press, and continue pressing, the Power button on the front panel of the system until the system powers on and either the Power LED stops blinking or the Power, UI, and Health LEDs are lit. Note: It takes approximately one minute for the system to enter boot mode. 4. Press and hold the Reset button, releasing after about one second, to scroll through the boot menu modes. The storage system shows the boot mode options using the LEDs, as described in the following table: Boot Mode Status Indicator Description Boot menu Normal Factory default OS reinstall Tech support Volume read only Memory test Test disk Power, UI, and Health LEDs blink. Health LED lights. UI LED lights. UI and Health LEDs light. Power LED lights. Power and Health LEDs light. Power and UI LEDs light. Power, UI, and Health LEDs light. Health UI LED LED Red Blue Red Blue Red Blue Red Blue Red Blue Power LED Green Green Green Green Green 5. Press and hold the Reset button for four seconds to confirm your boot menu selection. The system boots in the selected boot mode. Note: If you do not hold the Reset button long enough, the press moves the system to the next selection. Repeat the press and hold for one second to scroll through to your desired selection. ReadyNAS 3130 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
ReadyNAS 3130
25
NETGEAR ReadyNAS OS 6 Rack-Mount Storage Systems
•
Test disk
. Performs an offline full disk test. This process can take four hours or more,
depending on the size of your disks. Any problems are reported in the system logs, which
you can view using the local admin page. For more information about viewing the system
logs, see the
ReadyNAS OS 6.2 Software Manual
.
To access the boot menu:
1.
Power off your system.
2.
Using a straightened paper clip, press and hold the
Reset
button on the control panel.
3.
Press, and continue pressing, the
Power
button on the front panel of the system until the
system powers on and either the Power LED stops blinking or the Power, UI, and Health
LEDs are lit.
Note:
It takes approximately one minute for the system to enter boot mode.
4.
Press and hold the
Reset
button, releasing after about one second, to scroll through the
boot menu modes.
The storage system shows the boot mode options using the LEDs, as described in the
following table:
Boot Mode
Status Indicator
Description
Health
LED
UI
LED
Power
LED
Boot menu
Power, UI, and Health LEDs blink.
Red
Blue
Green
Normal
Health LED lights.
Red
Factory default
UI LED lights.
Blue
OS reinstall
UI and Health LEDs light.
Red
Blue
Tech support
Power LED lights.
Green
Volume read only
Power and Health LEDs light.
Red
Green
Memory test
Power and UI LEDs light.
Blue
Green
Test disk
Power, UI, and Health LEDs light.
Red
Blue
Green
5.
Press and hold the
Reset
button for four seconds to confirm your boot menu selection.
The system boots in the selected boot mode.
Note:
If you do not hold the
Reset
button long enough, the press moves the
system to the next selection. Repeat the press and hold for one second
to scroll through to your desired selection.