Nokia 002J2F3 User Manual - Page 13

Remove the memory card, Charge the battery, charger from the device, then from the wall outlet.

Get Nokia 002J2F3 PDF manuals and user guides View all Nokia 002J2F3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Get started Get started 1. Remove the back cover. 2. Insert the memory card into the memory card slot with the contact surface facing down, and press it until it locks into place. 3. Replace the back cover. Remove the memory card Important: Do not remove the memory card in the middle of an operation when the card is being accessed. Removing the card in the middle of an operation may damage the memory card as well as the device, and data stored on the card may be corrupted. You can remove or replace the memory card during phone operation without switching the device off. 1. Ensure that no application is currently accessing the memory card. 2. Remove the back cover. 3. Press the memory card slightly in to release the lock, and remove it. 4. Replace the back cover. Charge the battery Your battery has been precharged, but the charging levels may vary. 1. Connect the charger to a wall outlet. 2. Connect the charger to the device. 3. When the battery is fully charged, disconnect the charger from the device, then from the wall outlet. If the battery is completely discharged, it may take a few minutes before the charging indicator appears on the display or before any calls can be made. The charging time depends on the charger used. Charging a BL-4S battery with the AC-3 charger takes approximately 3 hours while the phone is in the standby mode. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
1.
Remove the back cover.
2.
Insert the memory card into the memory card slot
with the contact surface facing down, and press it
until it locks into place.
3.
Replace the back cover.
Remove the memory card
Important:
Do not remove the memory card in the middle of an operation
when the card is being accessed. Removing the card in the middle of an operation
may damage the memory card as well as the device, and data stored on the card
may be corrupted.
You can remove or replace the memory card during phone operation without
switching the device off.
1.
Ensure that no application is currently accessing the memory card.
2.
Remove the back cover.
3.
Press the memory card slightly in to release the lock, and remove it.
4.
Replace the back cover.
Charge the battery
Your battery has been precharged, but the charging levels may vary.
1.
Connect the charger to a wall outlet.
2.
Connect the charger to the device.
3.
When the battery is fully charged, disconnect the
charger from the device, then from the wall outlet.
If the battery is completely discharged, it may take a few
minutes before the charging indicator appears on the
display or before any calls can be made.
The charging time depends on the charger used. Charging a BL-4S battery with
the AC-3 charger takes approximately 3 hour
mode.
Get started
12
Get started
s while the phone is in the standby