NordicTrack C 2300 English Manual - Page 7

Attach each Extension Leg 102 with two 1 Tek Screws - console

Get NordicTrack C 2300 PDF manuals and user guides View all NordicTrack C 2300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

3. Cut the rubber band securing the Upright Wire Harness (98). Have a second person hold the console assembly 3 near the Uprights (69). Connect the Upright Wire Harness to the wires extending from the Console Base (81). The connectors should slide together easily and snap into place. If they do not, turn one connector and try again. Insert the connectors and the Upright Wire Harness down into the right Upright, and then set the console assembly on the Uprights. Be careful not to pinch the wires. Console Assembly 98 81 98 69 4. Insert a Handrail (118) into the right side of the console assembly as shown. (Note: It may be helpful to twist the Handrail as you insert it.) Next, insert two 4 1/2" Bolts (78) with Handrail Spacers (77) into the right Upright (69) and the Handrail. Be careful not to pinch the wires. Make sure that the Handrail Spacers are flush against the right Upright, with the thicker sides of the Handrail Spacers toward the center of the treadmill, as shown in the inset drawing. Next, lift the console assembly and the Handrail (118) slightly and align the 4 1/2" Bolts (78) with the holes in the Handrail. Thread the Bolts into the Handrail until the heads of the Bolts are against the right Upright (69). Do not tighten the Bolts yet. Attach the other Handrail (not shown) in the same way. Note: There are no wires on the left side. 5. With the help of a second person, carefully tip the Uprights (69) down to the position shown. Make sure that the Extension Legs (102) remain in the Uprights. Attach each Extension Leg (102) with two 1" Tek Screws (47). Next, align the lower ends of the Handrails (118) with the holes in the base of the Uprights (69). Attach each Handrail with a 4" Bolt (53) as shown. Note: The Bolts must be at an angle that matches the angle of the Handrails, as shown in the inset drawing. With the help of a second person, carefully tip the Uprights (69) back to the vertical position. See step 4. Tighten the four 4 1/2" Bolts (78). Note: One replacement Base Pad (99) may be included. Use the Base Pad to replace any Base Pad that becomes worn. 4 118 5 69 118 102 69 77 Thick Side 77 78 Console Assembly 99 53 47 99 99 102 53 47 99 53 118 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
78
77
Thick
Side
Console
Assembly
69
77
118
4
7
5.
With the help of a second person, carefully tip the
Uprights (69) down to the position shown.
Make sure that
the Extension Legs (102) remain in the Uprights.
Attach each Extension Leg (102) with two 1” Tek Screws
(47). Next, align the lower ends of the Handrails (118)
with the holes in the base of the Uprights (69). Attach
each Handrail with a 4” Bolt (53) as shown.
Note: The
Bolts must be at an angle that matches the angle of
the Handrails, as shown in the inset drawing.
With the help of a second person, carefully tip the
Uprights (69) back to the vertical position. See step 4.
Tighten the four 4 1/2” Bolts (78).
Note: One replacement Base Pad (99) may be included.
Use the Base Pad to replace any Base Pad that becomes
worn.
47
53
53
102
118
69
99
47
102
99
99
99
5
3.
Cut the rubber band securing the Upright Wire Harness
(98). Have a second person hold the console assembly
near the Uprights (69). Connect the Upright Wire Harness
to the wires extending from the Console Base (81).
The
connectors should slide together easily and snap into
place. If they do not, turn one connector and try again.
Insert the connectors and the Upright Wire Harness down
into the right Upright, and then set the console assembly
on the Uprights.
Be careful not to pinch the wires.
98
69
81
Console
Assembly
3
98
118
53
4.
Insert a Handrail (118) into the right side of the console
assembly as shown. (Note: It may be helpful to twist the
Handrail as you insert it.) Next, insert two 4 1/2” Bolts (78)
with Handrail Spacers (77) into the right Upright (69) and
the Handrail.
Be careful not to pinch the wires.
Make
sure that the Handrail Spacers are flush against the right
Upright, with the thicker sides of the Handrail Spacers to-
ward the center of the treadmill, as shown in the inset
drawing.
Next, lift the console assembly and the Handrail (118)
slightly and align the 4 1/2” Bolts (78) with the holes in the
Handrail. Thread the Bolts into the Handrail until the
heads of the Bolts are against the right Upright (69).
Do
not tighten the Bolts yet.
Attach the other Handrail (not shown) in the same way.
Note: There are no wires on the left side.