NordicTrack E 3700 Treadmill Uk Manual - Page 28

Troubleshooting

Get NordicTrack E 3700 Treadmill PDF manuals and user guides View all NordicTrack E 3700 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

TROUBLESHOOTING Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department. PROBLEM: The power does not turn on SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet (See page 9.) If an extension cord is needed, use only a 3-conductor, 1 mm2 (14-gauge) cord that is no longer than 1.5 m (5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets. b. After the power cord has been plugged in, make sure that the key is fully inserted into the console. c. Check the on/off circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the on/off circuit breaker has tripped. To reset the on/off circuit breaker, wait for five minutes and then press the on/off circuit breaker back in. c Tripped Reset PROBLEM: The power turns off during use SOLUTION: a. Check the on/off circuit breaker located on the treadmill frame near the power cord (see c. above). If the on/off circuit breaker has tripped, wait for five minutes and then press the switch back in. b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in. c. Remove the key from the console. Reinsert the key fully into the console. d. If the treadmill still will not run, please call our Customer Service Department. PROBLEM: The displays of the console do not function properly SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Carefully tip the treadmill down as a shown in drawing a. Remove the 1" Screws (33) and the 2" Screws (3) from the hood. Raise the Uprights (69) and carefully remove the hood. 33 Locate the Reed Switch (10) and the Magnet (7) on the left side of the Pulley (8). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 3 mm (1/8 in.). If necessary, loosen the Screw (100), move the Reed Switch slightly, and then retighten the Screw, re-attach the hood, making sure the screws are in the same holes. Run the treadmill for a few minutes to check for a correct speed reading. 69 3 mm 100 10 Top View 3 8 7 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department.
PROBLEM:
The power does not turn on
SOLUTION:
a. Make sure that the power cord is plugged into a properly earthed outlet (See page 9.) If an exten-
sion cord is needed, use only a 3-conductor, 1 mm
2
(14-gauge) cord that is no longer than 1.5 m
(5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the on/off circuit breaker located on the tread-
mill near the power cord. If the switch protrudes as
shown, the on/off circuit breaker has tripped. To reset
the on/off circuit breaker, wait for five minutes and
then press the on/off circuit breaker back in.
PROBLEM:
The power turns off during use
SOLUTION:
a. Check the on/off circuit breaker located on the treadmill frame near the power cord (see c.
above). If the on/off circuit breaker has tripped, wait for five minutes and then press the switch
back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five
minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. If the treadmill still will not run, please call our Customer Service Department.
PROBLEM:
The displays of the console do not function properly
SOLUTION:
a. Remove the key from the console and
UNPLUG THE
POWER CORD.
Carefully tip the treadmill down as
shown in drawing a. Remove the 1” Screws (33) and
the 2” Screws (3) from the hood. Raise the Uprights
(69) and carefully remove the hood.
Locate the Reed Switch (10) and the Magnet (7) on
the left side of the Pulley (8). Turn the Pulley until the
Magnet is aligned with the Reed Switch.
Make sure
that the gap between the Magnet and the Reed
Switch is about 3 mm (1/8 in.).
If necessary, loosen
the Screw (100), move the Reed Switch slightly, and
then retighten the Screw, re-attach the hood, making
sure the screws are in the same holes. Run the tread-
mill for a few minutes to check for a correct speed
reading.
28
7
33
3
69
a
8
100
3 mm
Top
View
10
Tripped
c
Reset