NordicTrack Ntxc8018 Instruction Manual - Page 5

Attach the Console 66 to the Upper Body Arm 27

Get NordicTrack Ntxc8018 PDF manuals and user guides View all NordicTrack Ntxc8018 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

b. Roughen the surface of the resistance pad with 100-grit sandpaper. Oil the leather resistance pad with one or two drops of light household oil. Spread the oil over the resistance pad. c. Oil the 3/8" washers and the thrust washer if needed. PROBLEM: The flywheel and/or the resistance strap offers no resistance. SOLUTION: a. Check the routing of the resistance strap. b. Make sure the flywheel is tight. Remove the "U" bolt cover from the flywheel (see page 9). Evenly tighten the two 1/4" nuts located on the right side of the flywheel. PROBLEM: The skis are slipping. SOLUTION: a. Wipe off any excess oil. b. Clean the bottom of the skis with a dry cloth or a small amount of mineral spirits or paint thinner. c. Make sure that the flywheel is tight. Remove the "U" bolt cover from the flywheel (see page 9). Evenly tighten the two 1/4" nuts located on the right side of the flywheel. PROBLEM: The rollers are squeaking or sticking. SOLUTION: See GENERAL LUBRICATION on page 10. 12 4. Lift the Upper body Arm (27) into position as shown. Be 4 sure the Snap Buttons (40) are fully extended and locked into position on both sides of the Hip Pad Slide (42). 27 40 42 5. The Console (66) requires two "AA" batteries (not included). Alkaline batteries are recommended. Refer to the inset drawing. Locate the Battery Door (89) on the back of the Console. Slide the Battery Door to the left and open it as shown. Press two batteries into the battery compartment, with the negative ends of the batteries touching the springs. Close the Battery Door and slide it to the right. Attach the Console (66) to the Upper Body Arm (27) by simply pressing it into place. 5 27 66 89 66 6. Plug the Console Wire (47) and the Pulse Monitor (49) into the jacks on the bottom of the Console (66) as shown. Plug the Console Wire (47) into the jack on the Upright (16). Batteries 6 66 Pulse Speed 49 47 16 47 7. Make sure that all parts are tightened before you use the ski exerciser. To protect the floor from damage, place a mat beneath the ski exerciser. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
12
5
4.
Lift the Upper body Arm (27) into position as shown.
Be
sure the Snap Buttons (40) are fully extended and
locked into position on both sides of the Hip Pad
Slide (42).
5.
The Console (66) requires two “AA” batteries (not includ-
ed). Alkaline batteries are recommended. Refer to the
inset drawing. Locate the Battery Door (89) on the back
of the Console. Slide the Battery Door to the left and
open it as shown. Press two batteries into the battery
compartment,
with the negative ends of the batteries
touching the springs.
Close the Battery Door and slide
it to the right.
Attach the Console (66) to the Upper Body Arm (27) by
simply pressing it into place.
6.
Plug the Console Wire (47) and the Pulse Monitor (49)
into the jacks on the bottom of the Console (66) as
shown.
Plug the Console Wire (47) into the jack on the Upright
(16).
7.
Make sure that all parts are tightened before you use the
ski exerciser.To protect the floor from damage, place a
mat beneath the ski exerciser.
b. Roughen the surface of the resistance pad with 100-grit sandpaper. Oil the leather resistance
pad with one or two drops of light household oil. Spread the oil over the resistance pad.
c. Oil the 3/8” washers and the thrust washer if needed.
PROBLEM:
The flywheel and/or the resistance strap offers no resistance.
SOLUTION:
a. Check the routing of the resistance strap.
b. Make sure the flywheel is tight. Remove the “U” bolt cover from the flywheel (see page 9). Evenly
tighten the two 1/4” nuts located on the right side of the flywheel.
PROBLEM:
The skis are slipping.
SOLUTION:
a.
Wipe off any excess oil.
b.
Clean the bottom of the skis with a dry cloth or a small amount of mineral spirits or paint thinner.
c.
Make sure that the flywheel is tight. Remove the “U” bolt cover from the flywheel (see page 9).
Evenly tighten the two 1/4” nuts located on the right side of the flywheel.
PROBLEM:
The rollers are squeaking or sticking.
SOLUTION:
See GENERAL LUBRICATION on page 10.
4
27
40
42
5
6
66
66
89
Batteries
27
47
49
Speed
Pulse
66
47
16