Oki MICROLINE 1120 Users Guide 3 - Page 38

Set Top of Form TOF

Get Oki MICROLINE 1120 PDF manuals and user guides View all Oki MICROLINE 1120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Set Top of Form (TOF) General Information The default top of form is set in the printer menu. The factory default for TOF is 11/12-inch (23.28 mm), equivalent to the distance down from the top of the sheet to the horizontal midpoint of the first line of printed characters. TOF.jpg You can establish one custom TOF setting for each feed path (Top Cut Sheet and Rear Continuous Form) and store it in the printer's memory. This selection will then automatically appear as the setting for TOF for the corresponding group in the Menu. You can also use the control panel switches to set a temporary TOF for one sheet or one continuous form. Use the Printer Menu panel.jpg Nota The printer default for TOF is 11/12-inch (23.8 mm). 1. Turn the printer on while holding down the SEL button. The printer enters the Menu. PRINTER CONTROL prints. 2. Press SEL repeatedly until the feed path for which you wish to change the TOF appears: REAR FEED or TOP FEED. 3. Press LF/FF repeatedly until CONTINUOUS PAPER TOP OF FORM or CUT SHEET TOP OF FORM prints. 4. Press LOAD/EJECT repeatedly until the setting you wish to engage prints. Choices are: 2.12 mm (1/12"), 3.18 mm (1/8"), 6.35 mm (1/4"), 7.62 mm (3/10"), 8.47 mm (1/3"), 10.58 mm (5/12"), 21.59 mm (0.85"), 23.28 mm (11/12"), 25.4 mm (1"), or 27.52 mm (13/12"). 5. Press and hold TEAR, then LOAD/EJECT, then LF/FF. This saves your setting and exits the menu mode. Microline 1120 User's Guide 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
Microline 1120 User’s Guide
38
Set Top of Form (TOF)
General Information
The default top of form is set in the printer menu.
The factory default for TOF is 11/12-inch (23.28 mm), equivalent to the
distance down from the top of the sheet to the horizontal midpoint of the
first line of printed characters.
TOF.jpg
You can establish one custom TOF setting for each feed path (Top Cut Sheet
and Rear Continuous Form) and store it in the printer’s memory. This
selection will then automatically appear as the setting for TOF for the
corresponding group in the Menu.
You can also use the control panel switches to set a temporary TOF for one
sheet or one continuous form.
Use the Printer Menu
panel.jpg
Nota
The printer default for TOF is 11/12-inch (23.8 mm).
1.
Turn the printer on while holding down the SEL button.
The printer enters the Menu.
PRINTER CONTROL
prints.
2.
Press SEL repeatedly until the feed path for which you wish to change
the TOF appears:
REAR FEED
or
TOP FEED
.
3.
Press LF/FF repeatedly until
CONTINUOUS PAPER TOP OF FORM
or
CUT SHEET TOP OF FORM
prints.
4.
Press LOAD/EJECT repeatedly until the setting you wish to engage
prints.
Choices are: 2.12 mm (1/12”), 3.18 mm (1/8”), 6.35 mm (1/4”),
7.62 mm (3/10”), 8.47 mm (1/3”), 10.58 mm (5/12”), 21.59 mm
(0.85"), 23.28 mm (11/12”), 25.4 mm (1”), or 27.52 mm (13/12”).
5.
Press and hold TEAR, then LOAD/EJECT, then LF/FF.
This saves your
setting and exits the menu mode.