Oki MICROLINE 690 Users Guide - Page 78

Testing the Printer, Font Sample Test

Get Oki MICROLINE 690 PDF manuals and user guides View all Oki MICROLINE 690 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Testing the Printer  Font Sample Test  Rolling ASCII Test  Hexadecimal Dump Mode Font Sample Test Important! Wide carriage Model ML691: If you are using 8.5" paper to run the tests, make sure the paper width selection in the printer menu is set to 8.5 inches. Otherwise, printing on the platen may damage the printer. See Chapter 4: Menu Mode for more information. The Font Sample Test prints a sample of the fonts standard to the printer. The top of the printout shows the Printer Model, Emulation (Epson, IBM compatible), Firmware (F/W) Revision Level, Flash Loader (LD) Revision Level, and Part Number. 1. Make sure paper is loaded. . Turn off the printer. . Press and hold the SEL + LF/FF keys while turning the printer back on. . When only the SEL indicator is blinking, hold down the LF/FF key and press the LOAD/EJECT key. The printer prints a page of font samples and the test ends. ML690/ML691 User's Guide 78

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
ML690/ML691 User’s Guide
¶·
Testing the Printer
Font Sample Test
Rolling ASCII Test
Hexadecimal Dump Mode
Font Sample Test
Important!
Wide carriage Model ML691: If you are using 8.5”
paper to run the tests, make sure the paper width
selection in the printer menu is set to 8.5 inches.
Otherwise, printing on the platen may damage
the printer. See Chapter 4: Menu Mode for more
information.
The Font Sample Test prints a sample of the fonts
standard to the printer.
The top of the printout shows the Printer Model,
Emulation (
E
pson,
I
BM compatible), Firmware
(
F/W
) Revision Level, Flash Loader (
LD
) Revision
Level, and Part Number.
Make sure paper is loaded.
Turn off the printer.
Press and hold the
SEL + LF/FF
keys while turning
the printer back on.
When only the
SEL
indicator is blinking, hold
down the
LF/FF
key and press the
LOAD/EJECT
key.
The printer prints a page of font samples and the
test ends.
1.
µ.
±.
².