Oki OKIPOS 441J LANBlack Users Guide - Page 29

Adjustment Mode

Get Oki OKIPOS 441J LANBlack PDF manuals and user guides View all Oki OKIPOS 441J LANBlack manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

6-4. Adjustment Mode There are the following seven adjustment modes. The device will enter the adjustment mode if your turn it on while pressing the FEED switch. (1) The Self Printing Mode is entered by releasing the FEED switch after the buzzer sounds once. (Refer to Section 6-4-1.) (Holding down for 2 more seconds) (2) Adjusting the Dot Alignment Mode is entered by releasing the FEED switch after the buzzer sounds twice. (Refer to Section 6-4-2.) (Holding down for 2 more seconds) (3) The Hexadecimal Dump Mode is entered by releasing the FEED switch after the buzzer sounds three times. (Refer to Section 6-4-3.) (Holding down for 2 more seconds) (4) The Black Mark Sensor Alignment Mode is entered by releasing the FEED switch after the buzzer sounds four times. (Refer to Section 6-4-4.) (Holding down for 2 more seconds) (5) The Near End Sensor Adjustment Mode is entered by releasing the FEED switch after the buzzer sounds five times. (Refer to the separate Specifications Manual for details.) (Holding down for 2 more seconds) (6) The Memory Switch Manual Setting Mode is entered by releasing the FEED switch after the buzzer sounds six times. (Refer to the separate Specifications Manual for details.) (Holding down for 2 more seconds) (7) The Memory Switch Override Mode is entered by releasing the FEED switch after the buzzer sounds seven times. (Refer to the separate Specifications Manual for details.) (Holding down for 2 more seconds) Returns to (1). - 25 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
– ²5 –
6-4.
Adjustment Mode
There are the following seven adjustment modes.
The device will enter the adjustment mode if your turn it on while pressing the FEED switch.
(±) The Self Printing Mode is entered by releasing the FEED switch after the buzzer sounds
once. (Refer to Section 6-4-±.)
(Holding down for ² more seconds)
(²)
Adjusting the Dot Alignment Mode is entered by releasing the FEED switch after the buzzer
sounds twice. (Refer to Section 6-4-².)
(Holding down for ² more seconds)
(³) The Hexadecimal Dump Mode is entered by releasing the FEED switch after the buzzer
sounds three times. (Refer to Section 6-4-³.)
(Holding down for ² more seconds)
(4) The Black Mark Sensor Alignment Mode is entered by releasing the FEED switch after
the buzzer sounds four times. (Refer to Section 6-4-4.)
(Holding down for ² more seconds)
(5)
The Near End Sensor Adjustment Mode is entered by releasing the FEED switch after the
buzzer sounds five times. (Refer to the separate Specifications Manual for details.)
(Holding down for ² more seconds)
(6)
The Memory Switch Manual Setting Mode is entered by releasing the FEED switch after
the buzzer sounds six times. (Refer to the separate Specifications Manual for details.)
(Holding down for ² more seconds)
(´) The Memory Switch Override Mode is entered by releasing the FEED switch after the
buzzer sounds seven times. (Refer to the separate Specifications Manual for details.)
(Holding down for ² more seconds)
Returns to (±).