Oki OKIPOS T410TT-Parallel Users Guide - Page 38

FACTORY/SERVICE TEST PRINT, Head Latch Lever, POWER

Get Oki OKIPOS T410TT-Parallel PDF manuals and user guides View all Oki OKIPOS T410TT-Parallel manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

FACTORY/SERVICE TEST PRINT The Factory/Service Test Label prints the internal operating parameters of the printer. 1. Open the print head by pushing the Head Latch Lever to the rear. 2. Press the LINE and FEED keys while simultaneously turning the POWER switch to the ON position. 3. When the printer beeps, release the LINE and FEED keys. The printer will then beep3 times indicating it is in the Factory/Service Print Test mode. 4. Latch the Print Head in the down position. 5. Press the LINE key to print a large (4" wide") Factory/Service Test Label. Press the FEED key to print a small (2" wide) Factory/Service Test Label. 6. The printer will begin printing a series of test labels, the first containing the operational parameters of the printer followed by one containing the internal printer settings. these two label formats will alternate until the FEED key is pressed, suspending the print operation. If the FEED key is pressed again, the printing will resume. 7. To remove the printer from the Factory/Service Print Test mode, remove power by placing the POWER switch in the OFF position. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
29
FACTORY/SERVICE TEST PRINT
The Factory/Service Test Label prints the internal operating parameters of the printer.
1. Open the print head by pushing the
Head Latch Lever
to the rear.
2. Press the
LINE
and
FEED
keys while simultaneously turning the
POWER
switch to
the ON position.
3. When the printer beeps, release the
LINE
and
FEED
keys. The printer will then beep3
times indicating it is in the Factory/Service Print Test mode.
4. Latch the Print Head in the down position.
5. Press the
LINE
key to print a large (4" wide") Factory/Service Test Label. Press the
FEED
key to print a small (2" wide) Factory/Service Test Label.
6. The printer will begin printing a series of test labels, the first containing the operational
parameters of the printer followed by one containing the internal printer settings. these
two label formats will alternate until the
FEED
key is pressed, suspending the print
operation. If the
FEED
key is pressed again, the printing will resume.
7. To remove the printer from the Factory/Service Print Test mode, remove power by
placing the
POWER
switch in the OFF position.