Olympus D-100 D-100 Instruction Manual - Page 92

When image protection, single-frame erasure, all-frame erasure or formatting is impossible - digital camera driver

Get Olympus D-100 PDF manuals and user guides View all Olympus D-100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

92 TROUBLESHOOTING When the monitor cannot display images Cause Remedy See The camera is in the shooting mode. Close the lens barrier and press the P. 42 monitor button so that the monitor turns on and displays an image. No image has been saved on the card The display shows message "NO PICTURE". P. 42 in use. Note that playback is possible only after images P. 89 are shot. The digital camera is connected to a The monitor turns off while the camera is P. 71 TV. connected to a PC. There is a problem with the card. Check the error message. P. 89 When image protection, single-frame erasure, all-frame erasure or formatting is impossible Cause Remedy See A write protect seal is attached to the Remove the seal. Note that the removed seal P. 25 card. should not be reused. When an error message is displayed during data downloading to the connected PC Cause Remedy See The cable is not connected properly. Check that it is connected properly. P. 81 The camera is off. Press the era on. monitor button to turn the cam- P. 30 The battery power is low. It is recommended to use the AC adapter P. 70 (optional) when the digital camera is connected to a PC. The USB driver is installed incorrectly Observe instructions given in the installation P. 81 in your PC. manual of the USB driver and make sure that the camera is recognized by your PC.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
92
TROUBLESHOOTING
Cause
Remedy
See
When the monitor cannot display images
The camera is in the shooting mode.
Close the lens barrier and press the
monitor button so that the monitor turns on and
displays an image.
P. 42
Cause
Remedy
See
When image protection, single-frame erasure, all-frame erasure or formatting is impossible
A write protect seal is attached to the
card.
Remove the seal. Note that the removed seal
should not be reused.
P. 25
Cause
Remedy
See
When an error message is displayed during data downloading to the connected PC
The cable is not connected properly.
Check that it is connected properly.
P. 81
P. 70
The camera is off.
Press the
monitor button to turn the cam-
era on.
The battery power is low.
It is recommended to use the AC adapter
(optional) when the digital camera is connected
to a PC.
The USB driver is installed incorrectly
in your PC.
Observe instructions given in the installation
manual of the USB driver and make sure that the
camera is recognized by your PC.
No image has been saved on the card
in use.
The display shows message “NO PICTURE”.
Note that playback is possible only after images
are shot.
P. 42
P. 89
The digital camera is connected to a
TV.
The monitor turns off while the camera is
connected to a PC.
P. 71
There is a problem with the card.
Check the error message.
P. 89
P. 30
P. 81