Olympus DW 90 DW-90 Instructions (English) - Page 5

Schedule Alarm Playback Function This is useful for reviewing your daily appointments and remainders. 1 Press and hold the MENU/FOLDER button for 1 second or longer. 2 Press the 9/+ or 0/- button to select the Schedule Alarm Playback Setup screen. "S" and "ALARM" flash on the display. 3 Press the PLAY button. 4 Press the 9/+ or 0/- button to select "On." 5 Press the PLAY button. The hour indicator flashes. 6 Press the 9/+ or 0/- button to select the hour. 7 Press the PLAY button to register the hour. Continue to set the minute. 8 Set the minute and press the STOP button. An alarm will sound at the scheduled time for 5 minutes. Press any button other than the DISPLAY or REC MODE button while the alarm is sounding to play back all files recorded in the day's date subfolder. To stop schedule alarm playback, press the a Alarm indicator STOP button. Notes • The alarm tone stops automatically if no button is pressed within 5 minutes after the alarm starts. The files recorded for the current date are not played back in this case. • Schedule alarm playback occurs every day unless it is set to OFF. • Even if no file is recorded in the day's date subfolder, the beeps will sound. In such a case, no sound is heard even if you press some button while the alarm is sounding. To cancel schedule alarm playback 1 Repeat steps 1 to 3 in "Schedule Alarm Playback Function." "On" flashes on the display. 2 Press the 9/+ or 0/- button to select "OFF." Schedule alarm playback is canceled. 3 Press the STOP button to close the menu. System Sounds The recorder beeps to alert you to button operations or warn you of errors. If you wish to disable the system sounds, proceed as follows: 1 Press and hold the MENU/FOLDER button for 1 second or longer. 2 Press the 9/+ or 0/- button to open the System Sound Setup screen. On the display, "bEEP" flashes. 3 Press the PLAY button. 4 Press the 9/+ or 0/- button to choose between "On" and "OFF." On: System sounds are enabled. OFF: System sounds are disabled. 5 Press the STOP button to close the menu. Note If the alarm playback function or the schedule alarm playback function has been set, the alarm will sound at the scheduled time even if the system sounds are disabled. Using the Microphone Stand When you place the recorder on a desk, etc. during recording, attach the supplied microphone stand to reduce unwanted vibration in the recorder. Attach the microphone stand Microphone stand Hold Set the HOLD switch to the HOLD position. All operation buttons are disabled. This feature is useful when the recorder has to be carried in a handbag or pocket. Remember to reset the HOLD switch before attempting to use the recorder. Notes • The recorder functions as follows with the HOLD switch set to the HOLD position: - If the recorder is stopped, the display goes dark. - If the recorder is playing, the display goes dark when playback of the current file has completed. - If the recorder is recording, the display goes dark when the recorder stops recording automatically upon running out of free memory. • When the display is dark because the HOLD switch is set to the HOLD position, you can make the clock flash for 2 seconds by pressing any button. • You can operate the following button and control while the HOLD switch is set to the HOLD position; - MICSENSE switch for selecting the microphone sensitivity - VOLUME control for adjusting the volume • The alarm will sound at the scheduled time even if the recorder is set to HOLD. The recorder will then begin to play the file associated with the alarm once you press any button. Resetting the Recorder (CLEAR) This also resets the current time and other settings to their initial status. 1 Holding STOP button pressed, press and hold the ERASE button for 2 seconds or longer. "CLEAR" and "YES" appear alternately on the display for 8 seconds. 2 Press and hold the ERASE button again within 4 seconds. All files in all folders are erased, and the recorder is reset to its default settings. Note If you leave the recorder untouched for 8 seconds or longer before you press the ERASE button in Step 2, Clear mode will be canceled, and the recorder will enter Stop mode.