Onkyo HT-RC260 Owner Manual
Onkyo HT-RC260 Manual
 |
View all Onkyo HT-RC260 manuals
Add to My Manuals
Save this manual to your list of manuals |
Onkyo HT-RC260 manual content summary:
- Onkyo HT-RC260 | Owner Manual - Page 1
AV Receiver HT-RC260 Instruction Manual Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new - Onkyo HT-RC260 | Owner Manual - Page 2
-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING AVIS RISK OF ELECTRIC SHOCK RISQUE DE CHOC ELECTRIQUE DO NOT OPEN operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may - Onkyo HT-RC260 | Owner Manual - Page 3
inside the unit is not user-serviceable. If you cannot turn on the unit, contact your Onkyo Hearing Loss Caution Excessive sound pressure from earphones and headphones accordance with the instructions, may cause which the receiver is connected. • Consult the dealer or an experienced radio/TV techni- - Onkyo HT-RC260 | Owner Manual - Page 4
(➔ 17) AM loop antenna (➔ 17) Speaker cable labels (➔ 11) Speaker setup microphone (➔ 23) Remote controller and two batteries (AA/R6) * In the Remote Controller To use the remote controller, point it at the AV receiver's remote control sensor, as shown below. Remote control sensor AV receiver - Onkyo HT-RC260 | Owner Manual - Page 5
V 56 Resetting REMOTE MODE Buttons 57 Resetting the Remote Controller 57 Controlling Other Components 57 Others Troubleshooting 59 Specifications 64 About HDMI 65 Using an RIHD-compatible TV, Player, or Recorder 66 Video Resolution Chart 68 To reset the AV receiver to its factory defaults - Onkyo HT-RC260 | Owner Manual - Page 6
• Onkyo Q for System Control • 4 Digital Inputs (2 Optical/2 Coaxial) • Component Video Switching (2 Inputs/1 Output) • Front "Line in" Input for Portable audio player • Universal Port for the Dock for iPod*/HD Radio™*6 tuner module • Banana Plug-Compatible Speaker Posts • Powered Zone 2 • Bi-Amping - Onkyo HT-RC260 | Owner Manual - Page 7
item. B ON/STANDBY button (➔ 19) C STANDBY indicator (➔ 19) D HDMI THRU indicator (➔ 45) E ZONE 2 indicator (➔ 49) F Remote control sensor (➔ 4) G ZONE 2, OFF, ZONE 2 LEVEL/TONE LEVEL and TONE buttons (➔ 47, 49 to 50) H Display (➔ 8) I LISTENING MODE buttons (➔ 28) J DIMMER button (➔ 20) K MEMORY - Onkyo HT-RC260 | Owner Manual - Page 8
) I Power cord J V REMOTE CONTROL jack K Composite video and analog audio jacks (BD/DVD IN, VCR/DVR IN and OUT, CBL/SAT IN, GAME IN, TV/CD IN) L ZONE 2 LINE OUT jacks M SUBWOOFER PRE OUT jacks N FRONT HIGH OR FRONT WIDE OR ZONE 2 SPEAKERS terminals See "Connecting the AV Receiver" for connection - Onkyo HT-RC260 | Owner Manual - Page 9
Controlling the AV Receiver B C *1 D E B F G H C I D J K E L*2 M N*3 F O To control the AV receiver, press RECEIVER to select Receiver mode. You can also use the remote controller to control Onkyo Blu-ray Disc/DVD player, CD player, and other components. See "Entering Remote Control Codes - Onkyo HT-RC260 | Owner Manual - Page 10
Home Theater Enjoying Home Theater Thanks to the AV receiver's superb capabilities, you can enjoy surround sound with a real sense of movement in your own home-just like being in a movie theater or concert hall. With Blu-ray Discs, you can enjoy DTS and Dolby Digital. With analog or digital TV - Onkyo HT-RC260 | Owner Manual - Page 11
the Speaker Cable Labels The AV receiver's positive (+) speaker terminals are all red (the negative (-) speaker terminals are all black). Speaker Front left, Front high left, Front wide left Front right, Front high right, Front wide right Center Surround left Surround right Surround back left, Zone - Onkyo HT-RC260 | Owner Manual - Page 12
connect more than one cable to each speaker terminal. Doing so may damage the AV receiver. • Don't connect one speaker to several terminals. Connecting the Speaker Cables Screw-type speaker terminals Strip 1/2" to 5/8" (12 to 15 mm) of insulation from the ends of the speaker cables, and twist the - Onkyo HT-RC260 | Owner Manual - Page 13
FRONT HIGH OR FRONT WIDE SPEAK- ERS terminals. When doing so, set "Surr Back/Front High/Front Wide" in Speaker Setup to "Front High" or "Front Wide" (➔ 36). Connecting a Powered Subwoofer Using a suitable cable, connect the AV receiver's SUBWOOFER PRE OUT jack to an input on your powered subwoofer - Onkyo HT-RC260 | Owner Manual - Page 14
image with AV components HDMI cable : Video & Audio Other cables AV receiver : Video : Audio AV receiver TV, projector, etc. Blu-ray Disc/ DVD player Game console TV, projector, etc. Blu-ray Disc/ DVD player Game console • Before making any AV connections, read the manuals supplied with - Onkyo HT-RC260 | Owner Manual - Page 15
channel (ARC) function enables an HDMI capable TV to send the audio stream to the HDMI OUT of the AV receiver. To use this function, you must select the TV/CD input selector. • To use ARC function, you must select the TV/CD input selector, your TV must support ARC function and "HDMI Control" is set - Onkyo HT-RC260 | Owner Manual - Page 16
Connecting External Components The on-screen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver's display when changing settings. Front " Rear $ # % & Connect your components to the - Onkyo HT-RC260 | Owner Manual - Page 17
AV receiver's remote controller to control your other V-capable Onkyo components, pointing the remote controller at the AV receiver's remote control sensor instead of the component. You must enter the appropriate remote control code first (➔ 56). Note • Use only V cables for V connections. V cables - Onkyo HT-RC260 | Owner Manual - Page 18
supported by your components. Use the following sections as a guide. The on-screen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver's display when changing settings. Video Connection - Onkyo HT-RC260 | Owner Manual - Page 19
Turning On/Off the AV Receiver ON/STANDBY STANDBY indicator ON/STANDBY RECEIVER Front panel Remote controller Turning On Press ON/STANDBY on the front panel. or Press RECEIVER followed by ON/STANDBY on the remote controller. The AV receiver comes on, the display lights, and the STANDBY indicator - Onkyo HT-RC260 | Owner Manual - Page 20
to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver's display when changing settings. This manual describes the procedure using the remote controller unless otherwise specified. Selecting the Language Used for the Onscreen Setup Menus You - Onkyo HT-RC260 | Owner Manual - Page 21
If the "Speakers Type" setting is set to "Bi-Amp" (➔ 35), or Powered Zone 2 is being used (➔ 49), this setting cannot be selected. • When the listening mode that doesn't support front high, front wide or surround back speakers is used, the setting cannot be selected. Using the Audio and Video Menus - Onkyo HT-RC260 | Owner Manual - Page 22
number of speakers. For the VCR/DVR input selector, the setting changes in this order: VCR/DVR ↔ DOCK Note • DOCK can be selected for the TV/CD, GAME or VCR/DVR input selector, but not at the same time. • Enter the appropriate remote control code before using the remote controller for the first - Onkyo HT-RC260 | Owner Manual - Page 23
home theater that SETUP MIC jack. SETUP MIC jack Speaker setup microphone The speaker setting menu appears. Note • The on-screen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver's display - Onkyo HT-RC260 | Owner Manual - Page 24
Room Correction and Speaker Setup again. Note that if the volume is set too high and the sound distorts, detection issues may occur, so use an appropriate volume level. If the subwoofer has a low-pass filter switch, set it to Off or Direct. Refer to your subwoofer's instruction manual for details - Onkyo HT-RC260 | Owner Manual - Page 25
, switch to manual tuning mode and listen to the station in mono. ■ Tuning into stations by frequency You can tune into AM and FM stations directly by entering the appropriate frequency. 1 On the remote controller, press TUNER repeatedly to select "AM" or "FM", followed by D.TUN. (Actual display - Onkyo HT-RC260 | Owner Manual - Page 26
again to store the station or channel. The station or channel is stored and the preset number stops displayed instead of the band and frequency. Selecting Presets To select a preset, use PRESET F/S on the AV receiver, or the remote controller's CH +/-. Tip • You can also use the remote controller - Onkyo HT-RC260 | Owner Manual - Page 27
VCR to the recording VCR without going through the AV receiver, connect the TV/VCR's audio and video outputs directly to the recording VCR's audio and video inputs. See the manuals supplied with your TV and VCR for details. • Video signals connected to composite video inputs can be recorded only via - Onkyo HT-RC260 | Owner Manual - Page 28
use with video games. STEREO button This button selects Stereo and All Channel Stereo listening modes. • The Dolby Digital and DTS listening modes can only be selected if your Blu-ray Disc/DVD player is connected to the AV receiver with a digital audio connection (coaxial, optical, or HDMI). • The - Onkyo HT-RC260 | Owner Manual - Page 29
Dolby Digital EX surround sound. This provides a center back surround channel from 5.1-channel sources. ■ Speaker Layout The illustration shows which speakers are activated in each channel. See "Speaker Configuration" for the speaker setup (➔ 36). ; 9 $ / Press RECEIVER followed by SP LAYOUT - Onkyo HT-RC260 | Owner Manual - Page 30
. The "Sp Config" (presence of speakers), "Sp Distance" and 4 "A/V Sync" settings are enabled, but much of the processing set via AUDIO % is disabled. See "Advanced Setup" for more details (➔ 33). ' ( ) Sound is output by the front left and right speakers and subwoofer. " 4 % Use this mode - Onkyo HT-RC260 | Owner Manual - Page 31
is output without surround-sound % processing. "Sp Config" (presence of speakers), "Crossover", "Sp Dis- tance", "A/V Sync" and much of the processing set via AUDIO are enabled. See "Advanced Setup" for more details (➔ 33). % ' % ' % Speaker Layout 9$/ 9$/ 9$/*1 9$/ 9$/*1 9$/ DTS DTS-HD - Onkyo HT-RC260 | Owner Manual - Page 32
Surround back and front wide speakers are not supported. *4 Front high and front wide speakers are not supported. *5 For the Blu-ray Discs, Dolby Digital is used in a 3.1/5.1-channel speaker system. *6 AV receiver can input the DSD signal from HDMI IN. Setting the output setting on the player side - Onkyo HT-RC260 | Owner Manual - Page 33
setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the composite video MONITOR OUT or the COMPONENT VIDEO OUT, use the AV receiver's display when changing settings. Remote indicator RECEIVER This manual describes the procedure using the remote controller - Onkyo HT-RC260 | Owner Manual - Page 34
(default setting underlined) Input/Output Assign Main Menu Input/Output Assign Monitor Out You can specify the output resolution for the HDMI OUT and COMPONENT VIDEO MONITOR OUT and have the AV receiver upconvert the picture resolution as necessary to match the resolution supported by your TV - Onkyo HT-RC260 | Owner Manual - Page 35
is connected, or • the "Audio TV Out" setting is set to "On" (➔ 44) and an input selector other than HDMI is selected. Speaker Settings If you change these settings, you must run Audyssey 2EQ Room Correction and Speaker Setup again (➔ 22). If you bi-amp the front speakers, you must change the - Onkyo HT-RC260 | Owner Manual - Page 36
the cutoff frequency of the LFE channel's low-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel. ■ Double Bass This setting is set automatically by Audyssey 2EQ® Room Correction and Speaker Setup function (➔ 22). With the Double - Onkyo HT-RC260 | Owner Manual - Page 37
the test tone (➔ 36). • The speakers cannot be calibrated while the AV receiver is muted. *1 For the center speaker and subwoofer, the level settings made by using the Audio menu are saved here as the default settings (➔ 21). Tip • If you're using a handheld sound level meter, adjust the level of - Onkyo HT-RC260 | Owner Manual - Page 38
, if you're using a center speaker, the center channel sound is output by only the center speaker. (If you're not using a center speaker, the center channel sound will be distributed to the front left and right speakers to create a phantom center). This setting controls the front left, right, and - Onkyo HT-RC260 | Owner Manual - Page 39
system each speaker level must be adjusted so that -30 dBFS band-limited (500 Hz to 2000 Hz) pink noise produces 75 dB sound pressure level at the listening position. A home theater system automatically calibrated by Audyssey 2EQ will play at reference level when the master volume control is set to - Onkyo HT-RC260 | Owner Manual - Page 40
speakers. About Audyssey Dynamic EQ Audyssey Dynamic EQ solves the problem of deteriorating sound quality TV picture while setting the delay, press ENTER. To return to the previous screen, press RETURN. If HDMI Lip Sync is enabled (➔ 44) and your TV or display supports HDMI Lip Sync, the displayed - Onkyo HT-RC260 | Owner Manual - Page 41
*1: Switches the displayed character remote con- troller by using +10. *2 Press CLR on the remote controller the TV picture while setting, press ENTER. video signal delay occurs during playback on a video component (i.e. game console), select the corresponding input source and set the "Game Mode" setting - Onkyo HT-RC260 | Owner Manual - Page 42
is set to "Auto", the AV receiver automatically detects the picture source and in either "3 : 2" or "2 : 2". However, there may be times when you will get a better picture by setting "Film Mode" yourself. Note • If the "Game Mode" setting is set to "On" (➔ 41), this setting is fixed at "Video - Onkyo HT-RC260 | Owner Manual - Page 43
`-50 to 0 to +50 With this setting you can adjust saturation. "-50" is the weakest color. "+50" is the strongest color. Tip *1 This procedure can also be performed on the remote controller by using the Video menu (➔ 21). *2 Press CLR if you want to reset to the default value. Listening Mode Preset - Onkyo HT-RC260 | Owner Manual - Page 44
is connected to the AV receiver via the HDMI cable, the name of the connected component is displayed on the AV receiver display. For example, while you are watching TV broadcasting, if you operate a Blu-ray Disc/DVD player (being powered on) by the remote control of the AV receiver, the name of the - Onkyo HT-RC260 | Owner Manual - Page 45
AV receiver. To use this function, you must select the TV/CD input selector and your TV must support ARC function. Note • The "Audio Return Channel" setting can be set only when the "HDMI Control" setting is set to "On". • This setting is set to "Auto" automatically when the "HDMI Control" is set - Onkyo HT-RC260 | Owner Manual - Page 46
input sources. Audio Selector You can set priorities of audio output when there are both digital and analog inputs. ■ Audio Selector ` ARC: The audio signal from your TV tuner can be sent to the HDMI OUT of the AV receiver.*1 With this selection the TV's audio can be automatically selected as - Onkyo HT-RC260 | Owner Manual - Page 47
. ` Analog: The AV receiver always outputs analog signals. Note • The setting is stored individually for each input selector. • This setting can be made only for the input source that is assigned as HDMI IN, COAXIAL IN, or OPTICAL IN. *1 You can select "ARC" if you select the TV/CD input selector - Onkyo HT-RC260 | Owner Manual - Page 48
AV receiver's FRONT HIGH OR FRONT WIDE OR ZONE 2 SPEAKERS L/R terminals. AV receiver Main room TV AV receiver Zone 2 IN R L Receiver/ integrated amp Note • The Zone 2 volume must be set on the Zone 2 amp. RL Zone 2 Note • With this setup, the Zone 2 volume is controlled by the AV receiver - Onkyo HT-RC260 | Owner Manual - Page 49
2, and how to adjust the volume for Zone 2. Controlling Zone 2 from the AV receiver ZONE 2 OFF - /+ Note • When "Zone2" is selected and Zone 2 turned on, the Zone 2 speakers connected to the FRONT HIGH OR FRONT WIDE OR ZONE 2 SPEAKERS terminals output sound, but the surround back, front high or - Onkyo HT-RC260 | Owner Manual - Page 50
(the ZONE 2 indicator and Zone 2 selector on the display flashes). 2 Use -/+ within 8 seconds to adjust the volume. If your Zone 2 speakers are connected to a receiver or integrated amp in Zone 2, use its volume control to adjust the volume. Muting Zone 2 ■ Operating with the remote controller Press - Onkyo HT-RC260 | Owner Manual - Page 51
control your iPod when "PORT" is selected as the input source. • See the UP-A1 Dock's instruction manual for more information. • See the RI Dock's instruction manual (➔ 53) for more information. *1 To use V (Remote Interactive), you must make an analog audio connection (RCA) between the AV receiver - Onkyo HT-RC260 | Owner Manual - Page 52
web site. For supported iPod models, see the instruction manual of the Onkyo Dock. UP-A1 Dock With the UP-A1 Dock, you can easily play the music, photo, or movie stored on your Apple iPod through the AV receiver and enjoy great sound. You can use the AV receiver's remote controller to operate your - Onkyo HT-RC260 | Owner Manual - Page 53
your iPod. Note • Enter the appropriate remote control code before using the AV receiver's remote controller for the first time (➔ 56). • Connect the RI Dock to the AV receiver with an V cable (➔ 51). • Set the RI Dock's RI MODE switch to "HDD" or "HDD/ DOCK". • Set the AV receiver's Input Display - Onkyo HT-RC260 | Owner Manual - Page 54
of the iPod, please refer to the instruction manual of RI Dock. *1 This button does not turn the Onkyo DS-A2 or DS-A2X RI Dock on or off. Your iPod may not respond the first time you press this button, in which case you should press it again. This is because the remote controller transmits the - Onkyo HT-RC260 | Owner Manual - Page 55
Onkyo Universal Port Option (➔ 53) Looking up for Remote Control Code You can look up for appropriate remote control code from on-screen setup menu. Note • This setting can be carried out by using On-screen Setup Menu only. Main menu Remote Controller Setup 1 Press RECEIVER followed by SETUP - Onkyo HT-RC260 | Owner Manual - Page 56
want to enter a code, press and hold down DISPLAY (about 3 seconds). The remote indicator lights. Note • Remote control codes cannot be entered for RECEIVER and ZONE 2. • Only TV remote control codes can be entered for TV. • Except for RECEIVER, TV and ZONE 2, remote control codes from any category - Onkyo HT-RC260 | Owner Manual - Page 57
Remote Control Codes" (➔ 56). Controlling a TV TV is preprogrammed with the remote control code for controlling a TV that supports the Q*1 (limited to some models). The TV must be able to receive remote control commands via Q and be connected to the AV receiver via HDMI. If controlling your TV - Onkyo HT-RC260 | Owner Manual - Page 58
The Q function is not supported. The Q supported by the AV receiver is the CEC system control function of the HDMI standard. *2 These buttons function as colored buttons or A, B, C, D buttons. *3 (Pause) functions as reverse playback. Note • See the "Controlling Your iPod" about the operation of - Onkyo HT-RC260 | Owner Manual - Page 59
until the remote indicator lights (about 3 seconds). Within 30 seconds, press RECEIVER again. The on-screen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver's display when changing settings - Onkyo HT-RC260 | Owner Manual - Page 60
the LFE channel, the subwoofer produces no sound. Make sure the speakers are configured correctly. 36 ■ There's no sound with a certain signal format Check the digital audio output setting on the con- - nected device. On some game consoles, such as those that support DVD, the default setting is off - Onkyo HT-RC260 | Owner Manual - Page 61
remote control code may not be correct. - If more than one code is listed, try each one. Move the AV receiver away from your TV or com- - puter. Listen to the station in mono. 25 UP-A1 Dock for iPod When listening to an AM station, operating the - remote controller may cause noise. Passing - Onkyo HT-RC260 | Owner Manual - Page 62
sure the correct input is selected on your TV or - the AV receiver. Some versions of the iPod do not output video. - ■ The AV receiver's remote controller doesn't control your iPod Make sure your iPod is properly inserted in the - Dock. If your iPod is in a case, it may not connect properly - Onkyo HT-RC260 | Owner Manual - Page 63
. Before disconnecting the power cord from the wall outlet, set the AV receiver to Standby. Important Note Regarding Video Playback The AV receiver can upconvert component video and composite video sources for display on a TV connected to the HDMI OUT. However, if the picture quality of the source - Onkyo HT-RC260 | Owner Manual - Page 64
" Weight 11.5 kg (25.4 lbs.) ■ HDMI Input Output Video Resolution Audio Format Supported IN 1, IN 2, IN 3, IN 4, IN 5, AUX INPUT OUT 1080p Dolby TrueHD, DTS Master Audio, DVD-Audio, DSD 3D, Audio Return Channel, Deep Color, x.v.Color, LipSync, CEC ■ Video Inputs Component Composite IN 1, IN - Onkyo HT-RC260 | Owner Manual - Page 65
for connecting TVs, projectors, Blu-ray Disc/DVD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components. With HDMI, a single cable can carry control signals, digital video, and up to eight channels of digital - Onkyo HT-RC260 | Owner Manual - Page 66
the video/audio from the antenna or from the input jack of the TV from the speakers connected to the AV receiver. (A connection such as optical digital cable or similar is required above the HDMI cable.) • Input to the AV receiver can be selected with the remote controller of the TV. • Operations - Onkyo HT-RC260 | Owner Manual - Page 67
etc. HDMI connection AV receiver DIGITAL AUDIO connection (OPTICAL) HDMI connection TV, projector, etc. 2. Connect the audio output from the TV to the OPTICAL IN 2 jack of the AV receiver using an optical digital cable. Note • When the audio return channel (ARC) function is used with TV for HDMI - Onkyo HT-RC260 | Owner Manual - Page 68
Chart The following tables show how video signals at different resolutions are output by the AV receiver. ✔: Output Input HDMI COMPONENT COMPOSITE Output HDMI 1080p 1080i 720p 480p 480i 1080p ✔ 1080i ✔ ✔ ✔ 720p ✔ ✔ ✔ 480p ✔ ✔ ✔ ✔ 480i ✔ ✔ ✔ ✔ ✔ 1080p ✔ 1080i ✔ ✔ ✔ 720p - Onkyo HT-RC260 | Owner Manual - Page 69
Memo En 69 - Onkyo HT-RC260 | Owner Manual - Page 70
Memo En 70 - Onkyo HT-RC260 | Owner Manual - Page 71
Memo En 71 - Onkyo HT-RC260 | Owner Manual - Page 72
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8163 ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/ ONKYO EUROPE ELECTRONICS
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
 |
 |
AV Receiver
HT-RC260
Instruction Manual
Thank you for purchasing an Onkyo AV Receiver.
Please read this manual thoroughly before making
connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new AV Receiver.
Please retain this manual for future reference.
Contents
Introduction
...................................
2
Connections
.................................
11
Turning On & Basic Operations
......
19
Advanced Operations
.................
33
Controlling iPod & Other
Components
............................
51
Others
...........................................
59
E
n