Onkyo HT-RC260 Owner Manual - Page 62
Recording, Zone 2, Others, Video ATT:OFF
View all Onkyo HT-RC260 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 62 highlights
Make sure the correct input is selected on your TV or - the AV receiver. Some versions of the iPod do not output video. - ■ The AV receiver's remote controller doesn't control your iPod Make sure your iPod is properly inserted in the - Dock. If your iPod is in a case, it may not connect properly to the Dock. Always remove your iPod from the case before inserting it into the Dock. The iPod cannot be operated while it's displaying the - Apple logo. Make sure you've selected the right remote mode. - When you use the AV receiver's remote controller, - point it toward your AV receiver. When connecting UP-A1 Dock to the radio tuner - UP-HT1 with AUTO selected by the tuner's Mode Selector switch, you can switch the input source between UP-A1 Dock and the tuner, by pressing PORT repeatedly on the front panel. If you still can't control your iPod, start playback by - pressing your iPod's Play button. Remote operation should then be possible. Try resetting your iPod. - Depending on your iPod, some buttons may not - work as expected. ■ The AV receiver unexpectedly selects your iPod as the input source Always pause iPod playback before selecting a dif- - ferent input source. If playback is not paused, the Direct Change function may select your iPod as the input source by mistake during the transition between tracks. Recording ■ Can't record On your recorder, make sure the correct input is - selected. To prevent signal loops and damage to the AV - receiver, input signals are not fed through to outputs with the same name (VCR/DVR IN to VCR/DVR OUT). Zone 2 ■ There's no sound Only components connected to analog inputs can be - played in Zone 2. ■ The Zone 2 speakers produce no sound Powered Zone 2 cannot be used if "Speakers Type" 35 is set to "Bi-Amp". To use the Zone 2 speakers, you must set the "Front 49 High/Front Wide/Zone2" setting to "Zone2". Others ■ The sound changes when I connect my headphones When a pair of headphones is connected, the listen- - ing mode is set to Stereo, unless it's already set to Stereo, Mono or Direct. ■ The speaker distance cannot be set as required In some cases, corrected values suitable for home - theater use may be set automatically. ■ How do I change the language of a multiplex source Use the "Multiplex" setting on the "Audio Adjust" 37 menu to select "Main" or "Sub". ■ The V functions don't work To use V, you must make an V connection and an 17 analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally. ■ The functions System On/Auto Power On and Direct Change don't work for components connected via V These functions don't work when Zone 2 is turned 17 on. ■ When performing "Audyssey 2EQ® Room Correction and Speaker Setup", the measurement fails showing the message "Ambient noise is too high.". This can be caused by any malfunction in your - speaker unit. Check if the unit produces normal sounds. ■ The following settings can be made for the composite video inputs You must use the buttons on the unit to make these settings. 1. While holding down the input selector button for the input source that you want to set, press SETUP. 2. Use F/S to change the setting. 3. Press the input selector button for the input source that you want to set when you've finished. • Video Attenuation This setting can be made for the BD/DVD, VCR/DVR, CBL/SAT, GAME, or AUX input. If you have a games console connected to the composite video input, and the picture isn't very clear, you can attenuate the gain. Video ATT:OFF: (default). Video ATT:ON: Gain is reduced by 2 dB. En 62