Onkyo HT-S5400 Owner Manual - Page 52

If the video source is connected to an HDMI input, 14, 35 you must assign that input to an input selector, and your TV must be connected to the HDMI OUT. On your TV, make sure that the video input to which - the AV receiver is connected is selected. ■ There's no picture from a source connected to an HDMI IN Reliable operation with an HDMI-to-DVI adapter is 57 not guaranteed. In addition, video signals from a PC are not guaranteed. ■ The on-screen menus don't appear On your TV, make sure that the video input to which - the AV receiver is connected is selected. When the AV receiver doesn't connect TV with - HDMI, onscreen menus are not displayed. Tuner ■ Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesn't light Relocate your antenna. - Move the AV receiver away from your TV or - computer. Listen to the station in mono. 22 When listening to an AM station, operating the - remote controller may cause noise. Passing cars and airplanes can cause interference. - Concrete walls weaken radio signals. - If nothing improves the reception, install an outdoor - antenna. Remote Controller ■ The remote controller doesn't work Before operating this unit, be sure to press - RECEIVER. Make sure that the batteries are installed with the 4 correct polarity. Install new batteries. Don't mix different types of 4 batteries, or old and new batteries. Make sure that the remote controller is not too far 4 away from the AV receiver, and that there's no obstruction between the remote controller and the AV receiver's remote control sensor. Make sure that the AV receiver is not subjected to - direct sunshine or inverter-type fluorescent lights. Relocate if necessary. If the AV receiver is installed in a rack or cabinet - with colored-glass doors, the remote controller may not work reliably when the doors are closed. Make sure you've selected the correct remote controller mode. 10, 48 Make sure you've entered the correct remote control 47 code. Make sure to set the same ID on both the AV 41 receiver and remote controller. ■ Can't control other components If it's an Onkyo component, make sure that the V 16 cable and analog audio cable are connected properly. Connecting only an V cable won't work. Make sure you've selected the correct remote controller mode. 10, 48 If you've connected a cassette tape deck, to the 32 TV/CD IN jack, or an RI Dock to the TV/CD IN or GAME IN or VCR/DVR IN jacks, for the remote controller to work properly, you must set the display. If you cannot operate it, you will need to enter the 47 appropriate remote control code. To control an Onkyo component that's connected 47 via V, point the remote controller at the AV receiver. Be sure to enter the appropriate remote control code first. To control an Onkyo component that's not 47 connected via V point the remote controller at the component. Be sure to enter the appropriate remote control code first. Recording ■ Can't record On your recorder, make sure the correct input is - selected. To prevent signal loops and damage to the AV - receiver, input signals are not fed through to outputs with the same name (e.g., VCR/DVR IN to VCR/DVR OUT). USB Device Playback ■ Can't access the music files on a USB device Make sure the USB device is plugged in properly. - The AV receiver supports USB devices that support 55 the USB mass storage device class. However, playback may not be possible with some USB devices even if they conform to the USB mass storage device class. USB memory devices with security functions cannot 21 be played. Others ■ Standby power consumption In the following cases, the power consumption may 42 reach up to a maximum of 37 W: - "HDMI Ctrl (RIHD)" setting is set to "On". (Depending on the TV status, the AV receiver will enter Standby mode as usual.) - The "HDMI Through" setting is set to other than "Off". ■ The sound changes when I connect my headphones When a pair of headphones is connected, the - listening mode is set to Stereo, unless it's already set to Stereo, Mono, or Direct. En 52