Onkyo R-805TX User Manual English - Page 15

Connecting the, remote control cables, AC outlet connection

Page 15 highlights

Connecting the remote control cables If your other components are made by ONKYO and those components are equipped with connectors, you can control the -connected components with the supplied remote controller. Before connecting • The unit must be connected in the system hookups for control operations. • Each component has two connectors. There is no difference between these connectors. • The components may be connected in any order. • The hookups on the previous page are necessary independently of the system hookups. The illustration below is an example of a hookup. Connections This unit (R-805TX) MD recorder Stereo cassette tape deck Audio CD recorder CD player remote control cable (supplied with every ONKYO component that has connectors except for the amplifier and receiver) • This is not an example of stacking the components. For the example, refer to page 9. AC outlet connection You can connect the power cord from another audio device to the rear of the R805TX. If the R-805TX is connected via an remote control cable to another Onkyo ANTENNA CDR OUT IN L TAPE OUT IN L AM R CD L FM 75 R OUT MD IN R LINE/DVD REMOTE CONTROL PROCESSOR L R OUT IN L R SPEAKERS CAUTION: SPEAKER IMPEDANCE 4 OHMS MIN. /SPEAKER AC OUTLET AC 230-240V 50Hz SWITCHED 100W MAX. audio device that has a STANDBY/ON but- ton, you can use the STANDBY/ON button 230-240 V, 50 Hz models 120 V, 60 Hz models on the R-805TX to turn on and off the power to both R-805TX and connected device, or place both devices in standby Capacity is 100 watts. Capacity is 120 watts. mode. When the R-805TX is turned on or placed in standby mode, electric current is always supplied to the AC connector on the rear panel. If you press the ENERGY SAVE button while the R-805TX is in standby mode, the power to the connected audio device will be turned off one minute later. (See page 20.) The shape and capacity of the AC outlet may differ depending on the area of purchase. Make sure that the capacity of other components connected to this unit does not exceed the capac- ity that is printed on the rear panel. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52

15
If your other components are made by ONKYO and those components are equipped with
connectors, you can control the
-connected components with the supplied remote control-
ler.
Before connecting
The unit must be connected in the
system hookups for
control operations.
Each component has two
connectors. There is no difference between these connectors.
The components may be connected in any order.
The hookups on the previous page are necessary independently of the
system hookups.
The illustration below is an example of a
hookup.
Connections
You can connect the power cord from
another audio device to the rear of the R-
805TX.
If the R-805TX is connected via an
remote control cable to another Onkyo
audio device that has a STANDBY/ON but-
ton, you can use the STANDBY/ON button
on the R-805TX to turn on and off the
power to both R-805TX and connected
device, or place both devices in standby
mode. When the R-805TX is turned on or
placed in standby mode, electric current is always supplied to the AC connector on the rear
panel. If you press the ENERGY SAVE button while the R-805TX is in standby mode, the power
to the connected audio device will be turned off one minute later. (See page 20.)
The shape and capacity of the AC outlet may differ depending on the area of purchase. Make
sure that the capacity of other components connected to this unit does not exceed the capac-
ity that is printed on the rear panel.
Connecting the
remote control cables
remote control cable (supplied with
every ONKYO component that has
connectors except for the amplifier and
receiver)
This unit
MD recorder
Stereo cassette
Audio
CD player
tape deck
(R-805TX)
This is not an example of stacking the
components. For the example, refer
to page 9.
CD recorder
AC outlet connection
L
R
SPEAKERS
OUT
IN
L
R
OUT
MD
CDR
TAPE
CD
IN
LINE/DVD
PROCESSOR
OUT
IN
OUT
IN
REMOTE
CONTROL
L
R
L
R
L
R
AM
FM
75
ANTENNA
CAUTION:
SPEAKER
IMPEDANCE
4 OHMS MIN.
/SPEAKER
AC OUTLET
AC 230-240V
50Hz
SWITCHED
100W MAX.
Capacity is 120 watts.
120 V, 60 Hz models
230-240 V, 50 Hz models
Capacity is 100 watts.