Onkyo TX-NR414 Owner Manual

Onkyo TX-NR414 Manual

Get Onkyo TX-NR414 PDF manuals and user guides View all Onkyo TX-NR414 manuals
Add to My Manuals
Save this manual to your list of manuals

Onkyo TX-NR414 manual content summary:

  • Onkyo TX-NR414 | Owner Manual - Page 1
    AV RECEIVER TX-NR414 Instruction Manual Contents Safety Information and Introduction 2 Table of Contents 6 Connections 12 Turning On & Basic Operations 19 Advanced Operations 39 Controlling Other Components 53 Appendix 59 Internet Radio Guide Remote Control Codes En
  • Onkyo TX-NR414 | Owner Manual - Page 2
    all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may
  • Onkyo TX-NR414 | Owner Manual - Page 3
    use only, recording copyrighted material is illegal without the permission of the copyright holder. 2. AC Fuse-The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact your Onkyo dealer. 3. Care-Occasionally you should dust the unit all over with a soft cloth. For
  • Onkyo TX-NR414 | Owner Manual - Page 4
    and fit a suitable plug. Fit a suitable fuse in the plug. For European Models Declaration of Conformity We, ONKYO EUROPE ELECTRONICS GmbH LIEGNITZERSTRASSE 6, 82194 GROEBENZELL, GERMANY declare in own responsibility, that the ONKYO product described in this instruction manual is in compliance with
  • Onkyo TX-NR414 | Owner Manual - Page 5
    the AV receiver's remote control sensor, as shown below. Remote control sensor AV receiver Approx. 16 ft. (5 m) En-5 Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will
  • Onkyo TX-NR414 | Owner Manual - Page 6
    Buttons 55 Remote Control Codes for Onkyo Components Connected via V 56 Resetting the REMOTE MODE Buttons 56 Resetting the Remote Controller 56 Controlling Other Components 57 Safety Information and Introduction Appendix Troubleshooting 59 Firmware Update 64 Connection Tips and Video Signal
  • Onkyo TX-NR414 | Owner Manual - Page 7
    kHz/24-bit D/A Converters • Powerful and Highly Accurate 32-bit Processing DSP • Jitter Cleaning Circuit Technology Connections • 6 HDMI Inputs and 1 Output • Onkyo Q for System Control • 4 Digital Inputs (2 Optical/2 Coaxial) • Component Video Switching (2 Inputs/1 Output) • Banana Plug-Compatible
  • Onkyo TX-NR414 | Owner Manual - Page 8
    B ON/STANDBY button (19) C ZONE 2, OFF buttons (52) D Remote control sensor (5) E Display (9) F LISTENING MODE buttons (30) G DIMMER button (North American and Taiwanese models) (36) H MEMORY button (28) I TUNING MODE button (27) J DISPLAY button (36) ST U K SETUP button (41) L TUNING R/X, PRESET
  • Onkyo TX-NR414 | Owner Manual - Page 9
    see the pages in parentheses. B Z2 (Zone 2) indicator (52) C 3D indicator This lights indicators RDS indicator (excluding North American and Taiwanese models) (28) AUTO indicator (27) TUNED indicator area O SLEEP indicator (36) P Channel/Unit indicators ch indicator Hz indicator m/ft indicator dB indicator
  • Onkyo TX-NR414 | Owner Manual - Page 10
    and Asian models) I VREMOTE CONTROL jack J Composite video and analog audio jacks (BD/DVD IN, CBL/SAT IN, GAME IN, PC IN, TV/CD IN) K ZONE 2 LINE OUT jacks L SUBWOOFER PRE OUT jack M MONITOR OUT V jack N AC INLET (Taiwanese models) See "Connecting the AV Receiver" for connection (➔ pages 12
  • Onkyo TX-NR414 | Owner Manual - Page 11
    Remote Controller Controlling the AV Receiver B C *1 BD E F CG H ID J E K L To control the AV receiver, press RECEIVER to select Receiver mode. You can also use the remote controller to control Onkyo Blu-ray Disc/DVD player, CD player, and other components. See "Entering Remote Control Codes" for
  • Onkyo TX-NR414 | Owner Manual - Page 12
    are using banana plugs, tighten the speaker terminal before inserting the banana plug. • Do not insert the speaker code directly into the center hole of the speaker terminal. Front right Front left Center Speaker Configuration Connections The following table indicates the channels you should
  • Onkyo TX-NR414 | Owner Manual - Page 13
    have contact with the AV receiver's rear panel. Doing so may damage the AV receiver. • Don't connect more than one cable to each speaker terminal. Doing so may damage the AV receiver. • Don't connect one speaker to several terminals. Using a Powered Subwoofer Connections LINE INPUT LINE INPUT
  • Onkyo TX-NR414 | Owner Manual - Page 14
    as coaxial. • Before making any AV connections, read the manuals supplied with your AV components. • Don't connect the power cord until you've completed and double-checked all AV connections. • Push plugs in all the way to make Right! good connections (loose connections can cause noise or
  • Onkyo TX-NR414 | Owner Manual - Page 15
    . Game console * If your TV doesn't support Audio Return Channel (ARC), you need to connect an optical digital cable together with the HDMI cable to the AV receiver. * When listening to an HDMI component through the AV receiver, set the HDMI component so that its video can be seen on the TV screen
  • Onkyo TX-NR414 | Owner Manual - Page 16
    menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver's display when changing settings. ✔: Assignment can be changed (➔ page 43). No. Jack/Port Components " AUX INPUT VIDEO Camcorder, etc AUDIO L/R # USB, AUX INPUT
  • Onkyo TX-NR414 | Owner Manual - Page 17
    V-capable components. • Connect only Onkyo components to V jacks. Connecting other manufacturer's components may cause a malfunction. • Some components may not support all V functions. Refer to the manuals supplied with your Onkyo components. • While Zone 2 is on, the System On/Auto Power On and
  • Onkyo TX-NR414 | Owner Manual - Page 18
    outlet. Note • Before connecting the power cord, connect all of your speakers and AV components. • Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the AV receiver into a different branch
  • Onkyo TX-NR414 | Owner Manual - Page 19
    New F/W" pops up. This notification only appears when the AV receiver is connected to your home network (➔ page 72). To perform the firmware update, follow the instructions on screen. Use the R/X and ENTER buttons on the AV receiver or remote controller to select one of the options, and then press
  • Onkyo TX-NR414 | Owner Manual - Page 20
    connected to other video outputs, use the AV receiver's display when changing settings. This section describes the procedure for using the remote controller, unless otherwise specified. Playing the Connected Component ■ Operating with the remote controller INPUT SELECTOR RECEIVER VOL R/X Turning
  • Onkyo TX-NR414 | Owner Manual - Page 21
    Controlling Contents of USB or Network Devices Press USB or NET first. I J B K C L D M E N F O G H P Q R B TOP MENU This button displays the top menu for each media or service the next song. Turning On & Basic Controlling Other Components" about the operation of other components
  • Onkyo TX-NR414 | Owner Manual - Page 22
    "USB" in the Home menu. 2 Connect the USB cable that comes with the iPod/iPhone to the USB port on the front of the AV receiver. While reading the contents of your iPod/iPhone, the message "Connecting..." appears on the AV receiver's display. A list of your iPod/iPhone model's contents appears
  • Onkyo TX-NR414 | Owner Manual - Page 23
    , and the NET indicator lights. If it flashes, verify that the Ethernet cable is firmly connected to the AV receiver. Tip • The same operation can be done by selecting "Network Service" in the Home menu. 2 Use R/X to select "vTuner Internet Radio" and then press ENTER. 3 Use R/X to select a program
  • Onkyo TX-NR414 | Owner Manual - Page 24
    . Note • Services available may vary depending on the region. See the separate instructions for more information. 1 Select "Network Setup" on the Setup menu to verify your IP address (➔ page 51). Take a note of the IP address. 2 On your computer, start your web browser. 3 Enter the AV receiver's IP
  • Onkyo TX-NR414 | Owner Manual - Page 25
    the AV receiver (Server Playback). 1 Start your computer or media server. 2 Press NET. The "NET" screen appears. The NET indicator lights. If it flashes, confirm the network connection. Tip • The same operation can be done by selecting "Network Service" in the Home menu. 3 Use R/X to select "DLNA
  • Onkyo TX-NR414 | Owner Manual - Page 26
    appear only on a TV that is connected to the HDMI OUT. Remote Playback means you can play the music files stored on a media server or personal computer with the AV receiver by operating the controller device in the home network. Windows Media Player 12 Setup This section explains how to configure
  • Onkyo TX-NR414 | Owner Manual - Page 27
    Turning On & Basic Operations ■ Manual tuning mode In manual tuning mode, FM stations will be in mono. 1 Press TUNING MODE so that the AUTO indicator goes off on the AV receiver stations directly by entering the appropriate frequency. 1 On the remote controller, press AM or FM to select "AM" or "FM
  • Onkyo TX-NR414 | Owner Manual - Page 28
    AV receiver, or the remote controller's CH +/-. Tip • You can also use the remote controller's number buttons to select a preset directly. Turning On & Basic Operations Using RDS (excluding North American and Taiwanese models AV receiver supports four types of RDS information: PS (Program Service)
  • Onkyo TX-NR414 | Owner Manual - Page 29
    broadcasting TP. 2 To locate a station that is broadcasting TP, press ENTER. The AV receiver searches until it finds a station that's broadcasting TP. If no stations are found, the message "Not Found" appears. Turning On & Basic Operations RDS program types (PTY) Type None News reports Current
  • Onkyo TX-NR414 | Owner Manual - Page 30
    Stereo listening mode and All Channel Stereo listening mode. PURE AUDIO button and indicator (European, Australian and Asian models) This button selects the Pure Audio listening mode. When this mode is selected, the AV receiver's display and video circuitry are turned off. The indicator lights when
  • Onkyo TX-NR414 | Owner Manual - Page 31
    and more accurate positioning of sounds. *1 The AV receiver outputs this source in 5.1-channel surround sound. Turning On & Basic Operations Speaker Layout The illustration shows which speakers are activated in each channel. See "Sp Config (Speaker Configuration)" for the speaker setup (➔ page 44
  • Onkyo TX-NR414 | Owner Manual - Page 32
    channels in 4 order to widen the stereo image a lively sound field with a powerful acoustic image, like Turning On & Basic Operations Description Input Source With this mode you can enjoy a virtual " surround sound even with only two or three 4 speakers. This works by controlling how % sounds
  • Onkyo TX-NR414 | Owner Manual - Page 33
    effects and vivid imaging. • Dolby PLII Movie Use this mode with DVDs and videos that bear the Dolby Surround logo or TV shows that feature Dolby Surround. You can also use this mode with stereo movies or TV shows and the AV receiver will create a 5.1 surround mix from the 2-channel stereo. • Dolby
  • Onkyo TX-NR414 | Owner Manual - Page 34
    will automatically switch to Direct. *3 The AV receiver can input the DSD signal from HDMI IN. Depending on the player, setting the output on the player side to PCM might bring better sound. *4 For the Blu-ray Discs, Dolby Digital is used in a 3.1/5.1-channel speaker system. • The listening modes
  • Onkyo TX-NR414 | Owner Manual - Page 35
    to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver's display when changing settings. 1 Press RECEIVER followed by HOME. The Home menu will be superimposed on the TV screen. Home Network Service USB InstaPrevue F/W Update Setup 2 Use R/X and ENTER to make the desired
  • Onkyo TX-NR414 | Owner Manual - Page 36
    timer, press SLEEP repeatedly until the SLEEP indicator goes off. • To check the time remaining until the AV receiver sleeps, press SLEEP. Note that if you press • (North American and Taiwanese models) Alternatively, you can use the AV receiver's DIMMER. Turning On & Basic Operations Displaying
  • Onkyo TX-NR414 | Owner Manual - Page 37
    models) Press MUSIC OPTIMIZER on the front panel. The M.Opt indicator lights on the AV receiver's display. The MUSIC OPTIMIZER indicator lights on the front panel. Tip • Alternatively, you can use the remote controller's Q SETUP. • See "Music Optimizer" for more details (➔ page 40). Turning
  • Onkyo TX-NR414 | Owner Manual - Page 38
    the listening mode is set to Stereo, unless it's already set to Stereo, Mono, Direct, or Pure Audio (European, Australian and Asian models). • If you connect an iPod or iPhone to the USB port on the AV receiver, no sound will be output from the headphones jack. Turning On & Basic Operations En-38
  • Onkyo TX-NR414 | Owner Manual - Page 39
    ■ Setup menu (HOME) The Setup menu (HOME) provides a convenient way to change the AV receiver's various settings. Settings are organized into 11 categories. The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver
  • Onkyo TX-NR414 | Owner Manual - Page 40
    or "Off" automatically. ` Off ` On Advanced Operations Turn this setting on to reduce the dynamic range of Dolby sound quality of compressed music files. When set to "On", the M.Opt indicator lights on the AV receiver's display, and the MUSIC OPTIMIZER indicator (North American and Taiwanese models
  • Onkyo TX-NR414 | Owner Manual - Page 41
    -HD High Resolution Audio, DTS-HD Master Audio and DTS Express. Note • The CinemaFILTER may not work when used with certain input sources. Using the Setup Menu (HOME) RECEIVER Remote indicator ENTER R/X/F/S HOME RETURN 1 Press RECEIVER followed by HOME. 2 Use R/X to select "Setup", and then
  • Onkyo TX-NR414 | Owner Manual - Page 42
    function reduces power consumption when the AV receiver is in standby mode. The HYBRID STANDBY indicator will light in either of the following conditions: - "HDMI Through" is enabled and Zones are turned off (the HDMI indicator is off). - "Network Standby" is enabled and Zones are turned off (the
  • Onkyo TX-NR414 | Owner Manual - Page 43
    to assign HDMI1 - HDMI6 to other input selectors. Note • If no video component is connected to HDMI output (even if the HDMI input is assigned), the AV receiver selects the video source based on the setting of "Component (Component Video Input)". • When an HDMI IN is assigned to an input selector
  • Onkyo TX-NR414 | Owner Manual - Page 44
    Digital Audio (Digital Audio Input) 1 2 3 4 5 "Setup" Menu Digital Audio If you connect a component to a digital audio input, you must assign that input to an input selector. For example, if you connect your CD player to the OPTICAL IN 1, you must assign "OPTICAL1" to the "TV/CD" input
  • Onkyo TX-NR414 | Owner Manual - Page 45
    response in the manuals supplied with your speakers and set accordingly. • Choose a higher crossover frequency if you want more sound from your subwoofer. ■ Double Bass ` On ` Off Turn this setting on to boost bass output by feeding bass sounds from the front left, right, and center channels to the
  • Onkyo TX-NR414 | Owner Manual - Page 46
    the front left and right speakers to create a phantom center). This setting controls the front left, right, and center mix, allowing you to adjust the weight of the center channel sound. DTS Advanced Operations ■ Neo:6 Music Center Image `0 to 2 to 5 With this setting, you can specify by how much
  • Onkyo TX-NR414 | Owner Manual - Page 47
    A/V Sync Source Setup ■ A/V Sync picture and sound are whether your TV or display supports HDMI Lip Sync and (European, Australian and Asian models) or Direct listening mode is , TV, CD, TAPE, iPod: To reset to the default, select "- - -". the HDMI OUT of the AV receiver.*1 With this selection, the
  • Onkyo TX-NR414 | Owner Manual - Page 48
    Setup" Menu OSD Hardware ■ Volume OSD ` On ` Off Turn this setting on to display the volume level on the TV screen while it is adjusted. Remote ID ■ Remote ID ` 1, 2, or 3 When several Onkyo components are used in the same room, their remote ID codes may overlap. To differentiate the AV receiver
  • Onkyo TX-NR414 | Owner Manual - Page 49
    the setting to "Off". • Refer to the connected component's instruction manual for details. • When the "HDMI Ctrl (RIHD)" setting is set to "On", the power consumption in standby mode slightly increases. (Depending on the TV status, the AV receiver will enter standby mode as usual.) • When the
  • Onkyo TX-NR414 | Owner Manual - Page 50
    "Audio Return Ch", turn off the power on all connected pieces of equipment and then turn them on again. Refer to the user's manuals for all connected pieces of equipment. Network Setup Advanced Operations 1 2 3 4 5 "Setup" Menu Network Setup After modifying the network settings, you must
  • Onkyo TX-NR414 | Owner Manual - Page 51
    AV receiver is in standby mode. Note that the indicator may not light under certain conditions (➔ page 42). Note • When set to "On", the power consumption slightly increases in standby mode. ■ Update Notice ` Enable ` Disable When this setting is enabled, you will be notified if a firmware update
  • Onkyo TX-NR414 | Owner Manual - Page 52
    source for each room. Making Zone 2 Connections Connecting the Zone Speakers to an Additional Amplifier This setup allows 5.1-channel playback in your main listening room and 2-channel stereo playback in Zone 2. Main room TV AV receiver Zone 2 IN R L Receiver/ integrated amp Note • The volume
  • Onkyo TX-NR414 | Owner Manual - Page 53
    from the Apple web site. For supported iPod/iPhone models, see the instruction manual of the Onkyo Dock. RI Dock With the RI Dock, you can easily play the music stored on your Apple iPod/iPhone through the AV receiver and enjoy great sound, and watch iPod/iPhone slideshows and videos on your TV. In
  • Onkyo TX-NR414 | Owner Manual - Page 54
    a remote control code (➔ page 55). See the Dock's instruction manual for more information. RI Dock • Set the RI Dock's RI MODE switch to "HDD" or "HDD/DOCK". • SOURCE may not work with a remote control code (without V). In this case, make an V connection and enter the remote control code 81993
  • Onkyo TX-NR414 | Owner Manual - Page 55
    , and the multi zone button, remote control codes from any category can be assigned for the REMOTE MODE buttons. However, these buttons also work as input selector buttons (➔ page 20), so choose a REMOTE MODE button that corresponds with the input to which you connect your component. For example, if
  • Onkyo TX-NR414 | Owner Manual - Page 56
    the AV receiver, and operate the component. Controlling Onkyo components without V If you want to control an Onkyo component by pointing the remote controller directly at it, or you want to control an Onkyo component that's not connected via V, use the following remote control codes: ` 30627: Onkyo
  • Onkyo TX-NR414 | Owner Manual - Page 57
    /DVD is preprogrammed with the remote control code for controlling a component that supports the Q*1 (limited to some models). The component must be able to receive remote control commands via Q and be connected to the AV receiver via HDMI. Use the following remote control codes: ` 32910/33101/33501
  • Onkyo TX-NR414 | Owner Manual - Page 58
    tape deck operation Available buttons F , U (Reverse Playback I SOURCE K MUTING Controlling Other Components ■ Satellite receiver / Cable receiver operation Available buttons C GUIDE D R/X/F/S ENTER E SETUP F ,  G A (Red) B (Green) C (Yellow) D (Blue) H Number: 1 to 9, 0 Number: +10
  • Onkyo TX-NR414 | Owner Manual - Page 59
    down HOME until the remote indicator lights (about 3 seconds). Within 30 seconds, press RECEIVER again. The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver's display when changing settings. Power ■ Can't turn
  • Onkyo TX-NR414 | Owner Manual - Page 60
    sound with a certain signal format Check the digital audio output setting on the - connected device. On some game consoles, such as those that support DVD, the default setting is off. With some DVD-Video and the DTS - bitstream stops, the AV receiver remains in DTS listening mode and the dts
  • Onkyo TX-NR414 | Owner Manual - Page 61
    the remote controller at that component. To control an Onkyo component that's connected via 55 V, point the remote controller at the AV receiver. Be sure to enter the appropriate remote control code first. To control an Onkyo component that's not connected 56 via V, point the remote controller at
  • Onkyo TX-NR414 | Owner Manual - Page 62
    connect to a server or Internet radio station, recheck the AV receiver's IP address on the "Network Setup" screen. Check the "Network Setup". 50 Appendix USB Device Playback ■ Can't access the music files on a USB device Make sure the USB device is plugged in properly. - The AV receiver supports
  • Onkyo TX-NR414 | Owner Manual - Page 63
    System On/Auto Power On and Direct Change don't work for components connected via V These functions don't work when Zone 2 is turned 17 on. ■ The following settings can be made for the composite video inputs You must use the buttons on the unit to make these settings. On the AV receiver, press the
  • Onkyo TX-NR414 | Owner Manual - Page 64
    AV receiver allows you to update the firmware using network connection on the rear panel. Note • Make sure your AV receiver and TV are turned on and an Ethernet cable is connected to the rear panel of the AV receiver. • Never unplug or turn off the AV receiver while it is being updated. • Never plug
  • Onkyo TX-NR414 | Owner Manual - Page 65
    disconnect then reconnect the AC power cord and try again. Case 4: If an error occurs due to a wrong selection of input sources, turn off and on the AV receiver. Then retry the update. Case 5: If you do not have an Internet connection to the network, please contact Onkyo Support (➔ page 67). En-65
  • Onkyo TX-NR414 | Owner Manual - Page 66
    minutes to complete the firmware update. • The AV receiver will retain all your settings after the update is finished. Before you start • Set the "HDMI Ctrl (RIHD)" setting to "Off" (➔ page 49). • Turn off the controller device connected via Ethernet cable. • Turn off Multi Zone if this function is
  • Onkyo TX-NR414 | Owner Manual - Page 67
    persists, please contact Onkyo Support and provide the error code. Case 3: If an error occurs during the update process, disconnect then reconnect the AC power cord and try again. Case 4: If an error occurs due to a wrong selection of input sources, turn off and on the AV receiver. Then retry the
  • Onkyo TX-NR414 | Owner Manual - Page 68
    you choose will depend on the formats supported by your components. Use the following sections as a guide. The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver's display when changing settings. Note • The on
  • Onkyo TX-NR414 | Owner Manual - Page 69
    TV. • The AV receiver will enter standby mode when the power of the TV is turned to standby. • You can set on the menu screen of the TV to either output the audio from the speakers connected to the AV receiver, or from the speakers of the TV. • It is possible to output the video/audio coming from
  • Onkyo TX-NR414 | Owner Manual - Page 70
    use the AV receiver for the first time, when the settings of each component are changed, when the main power of each component is turned off, when the power cable is disconnected from the power supply, or when there has been a power outage. Appendix 4 Operate with the remote controller. For buttons
  • Onkyo TX-NR414 | Owner Manual - Page 71
    PC are not supported. • The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the picture is poor or there's no sound from a component connected via HDMI, check its setup. Refer to the connected component's instruction manual for details. En
  • Onkyo TX-NR414 | Owner Manual - Page 72
    Consult your ISP if you have any problems with your Internet connection. • The AV receiver uses DHCP to configure its network settings automatically. If you want to configure these settings manually, see "Network Setup" (➔ page 50). • The AV receiver does not support PPPoE settings, so if you have
  • Onkyo TX-NR414 | Owner Manual - Page 73
    , the message "No Storage" will be displayed. • If you connect a USB hard disk drive to the AV receiver's USB port, we recommend that you use its AC adapter to power it. • The AV receiver supports USB MP3 players that support the USB Mass Storage Class standard, which allows USB devices to be
  • Onkyo TX-NR414 | Owner Manual - Page 74
    of wired and wireless interoperable networks where digital content such as photos, music, and videos can be shared through consumer electronics, personal computers, and mobile devices in and beyond the home. The AV receiver complies with the DLNA Interoperability Guidelines version 1.5. En-74
  • Onkyo TX-NR414 | Owner Manual - Page 75
    DLNA Logo and DLNA CERTIFIED™ are trademarks, service marks, or certification marks of the Digital Living Network Alliance." Windows and the Windows logo are trademarks of the Microsoft group of companies. InstaPrevue and the InstaPrevue logo are trademarks or registered trademarks of Silicon Image
  • Onkyo TX-NR414 | Owner Manual - Page 76
    - 1611/1710 kHz Preset Channel 40 General Appendix Power Supply (North American and Taiwanese Supported ■ Video Inputs IN 1, IN 2, IN 3, IN 4, IN 5, IN 6 OUT 1080p Dolby True HD, DTS-HD Master Audio, DVD-Audio, DSD 3D, Audio Return Channel, DeepColor, x.v.Color, LipSync, CEC (RIHD) Component
  • Onkyo TX-NR414 | Owner Manual - Page 77
    ■ Video Outputs Component Composite ■ Audio Inputs OUT MONITOR OUT Digital Analog Optical: 2 Coaxial: 2 BD/DVD, CBL/SAT, GAME, PC, TV/CD, AUX ■ Audio Outputs Analog ZONE2 LINE OUT
  • Onkyo TX-NR414 | Owner Manual - Page 78
    Memo Appendix En-78
  • Onkyo TX-NR414 | Owner Manual - Page 79
    Memo Appendix En-79
  • Onkyo TX-NR414 | Owner Manual - Page 80
    Fax: +49-8142-4401-555 http://www.eu.onkyo.com/ The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK Tel: +44-(0)1628-473-350 Fax: +44 Fax: 86-21-52130396 http://www.cn.onkyo.com/ SN 29400992 (C) Copyright 2012 ONKYO SOUND & VISION CORPORATION Japan. All rights reserved. Y1112-1 * 2 9 4
  • Onkyo TX-NR414 | Owner Manual - Page 81
    of the network services appears, and the NET indicator lights. If it flashes, verify that the Ethernet cable is firmly connected to the AV receiver. 2 Select the desired service and press ENTER. The top page of the selected service appears. Using Multiple Accounts The AV receiver supports multiple
  • Onkyo TX-NR414 | Owner Manual - Page 82
    service that code on your TV screen. Please write down this code. Go to an Internet connected computer and point your browser to www.pandora.com/onkyo Enter your activation code and then follow the instructions account to your Onkyo receiver by selecting "I and allow you to buy them all from Amazon
  • Onkyo TX-NR414 | Owner Manual - Page 83
    /onkyo If in Web Setup. ■ Using Guide: You can play tracks from Genres, Top Artists, Top Albums, Top Tracks, New Releases, and Staff Picks. Rhapsody Channels: Listen to radio channels control the tracks with the buttons on the remote control. Enabled buttons RANDOM, REPEAT Note • On Rhapsody Channels
  • Onkyo TX-NR414 | Owner Manual - Page 84
    AV receiver connected to the Internet. Using the remote control, follow these steps: 1 Use R/X to select "Sign In", and then press ENTER. If you have an existing SIRIUS account, you can sign in by selecting "Sign In". Enter your user name and password in the next keyboard screen, or in Web Setup
  • Onkyo TX-NR414 | Owner Manual - Page 85
    reviews and an endless choice of personalised, ad-free radio stations, Last.fm is a great way to discover music. Pick up your free Last.fm account today at www.last.fm/join Get a subscription and you can enjoy the best of ad-free Last.fm Radio on your Onkyo AV receiver . Latest prices and full
  • Onkyo TX-NR414 | Owner Manual - Page 86
    then press ENTER. The keyboard screen appears. You can enter information from the remote control or the keys on the main unit. 2 If there are no mistakes Access without Sign In" and press ENTER to use a restricted version of the service. Note that use will be restricted. Tip • If you want to use
  • Onkyo TX-NR414 | Owner Manual - Page 87
    tracks with the buttons on the remote control. Enabled buttons ■ Menu Items Ratings and favorites: Rate the currently showing Show or Episode. More Episode in this Show: List information about the currently playing Show or Episode. Add episode to My Channel: Add the currently playing Episode to
  • Onkyo TX-NR414 | Owner Manual - Page 88
    Memo Using Internet Radio En-8
  • Onkyo TX-NR414 | Owner Manual - Page 89
    AV. 2 Sélectionnez le service désiré et appuyez sur ENTER. La page principale du service sélectionné s'affiche. Utilisation de plusieurs comptes L'ampli-tuner AV • Pour commuter entre les comptes, vous devez d'abord vous déconnecter du compte actuel, puis vous reconnectez depuis l'écran « Users ».
  • Onkyo TX-NR414 | Owner Manual - Page 90
    Radio -Pour commencer (États-Unis uniquement) Pandora est un service de radio en ligne libre et personnalisé vous permettant Internet et connectez le navigateur à www.pandora.com/onkyo Saisissez votre code d'activation puis suivez les instructions pour créer votre compte Pandora et vos stations
  • Onkyo TX-NR414 | Owner Manual - Page 91
    en créer un à partir de www.rhapsody.com/onkyo Si vous possédez déjà un compte Rhapsody, sélectionnez artiste, par album ou par piste. Music Guide : Vous pouvez lire des pistes à partir listes de lecture en cours de lecture. Add channel to My Channels : Marquez les canaux de radio Rhapsody en cours
  • Onkyo TX-NR414 | Owner Manual - Page 92
    du Nord uniquement) Votre ampli-tuner AV Onkyo comprend un essai gratuit de SiriusXM Internet Radio. L'écran « Account Info » affiche le nombre de jours restants dans votre essai. Une fois la période d'essai expirée, si vous souhaitez continuer à écouter le service, vous devez vous abonner. Pour
  • Onkyo TX-NR414 | Owner Manual - Page 93
    service de musique qui apprend ce que vous aimez... Votre nouvel ampli-tuner AV Onkyo sur votre ampli-tuner AV Onkyo sans ordinateur ! Recommended fm, vous pouvez vous y connecter pour sélectionner « Sign in Sign Out : Pour vous déconnecter de votre compte. 3 Utilisez services de webradio fournis par un
  • Onkyo TX-NR414 | Owner Manual - Page 94
    puis appuyez sur ENTER pour utiliser une version restreinte du service. Veuillez noter que l'utilisation est restreinte. Conseil • R/X pour sélectionner un élément du menu, puis appuyez sur ENTER. Pour vous déconnecter, utilisez R/X pour sélectionner « Sign out » depuis cet écran, puis appuyez sur
  • Onkyo TX-NR414 | Owner Manual - Page 95
    code d'association à partir du site Web de Mediafly (http://www.mediafly.com/DigitalLifestyle) à l'aide de votre ordinateur. Après avoir créé un compte, revenez à l'ampli-tuner AV un élément du menu, puis appuyez sur ENTER. Pour vous déconnecter, sélectionnez « Sign out » depuis cet écran, puis
  • Onkyo TX-NR414 | Owner Manual - Page 96
    Mémo Utilisation d'une webradio Fr-8
  • Onkyo TX-NR414 | Owner Manual - Page 97
    lista de los servicios de red y se iluminará el indicador NET. Si parpadea, verifique que el cable Ethernet esté firmemente conectado al receptor de AV. 2 Seleccione el servicio deseado y pulse ENTER. Aparecerá la página principal del servicio seleccionado. Uso de múltiples cuentas El receptor de
  • Onkyo TX-NR414 | Owner Manual - Page 98
    activación en la pantalla del televisor. Tome nota de este código. Vaya a un ordenador conectado a Internet y dirija el navegador a www.pandora.com/onkyo Introduzca su código de activación y siga las instrucciones para crear su cuenta de Pandora y sus emisoras de radio por Internet personalizadas de
  • Onkyo TX-NR414 | Owner Manual - Page 99
    todavía no tiene una, puede crear una nueva en www.rhapsody.com/onkyo Si ya tiene una cuenta Rhapsody, seleccione "Sign in to your Guide: Puede reproducir canciones por géneros, artistas principales, álbumes principales o canciones principales, novedades, selección del sitio. Rhapsody Channels
  • Onkyo TX-NR414 | Owner Manual - Page 100
    Internet Radio (solo Norteamérica) Su receptor de AV Onkyo incluye una prueba gratuita de SiriusXM Internet Radio. La una contraseña que deberá introducir en el receptor de AV. Para poder utilizar SiriusXM Internet Radio, el receptor de AV debe estar conectado a internet. Para usar el mando
  • Onkyo TX-NR414 | Owner Manual - Page 101
    lo mejor de Last.fm Radio sin anuncios en su receptor de AV Onkyo sin necesidad de un ordenador. Recommended Radio: Descubra nuestras interesantes Favorites: Añade una emisora a la lista Mis favoritos. ■ Uso del control de scrobbling Utilice R/X para seleccionar "Enable", y luego pulse ENTER. *
  • Onkyo TX-NR414 | Owner Manual - Page 102
    á la pantalla de teclado. Puede introducir información desde el mando a distancia o desde el teclado de la unidad principal. 2 Si no hay errores en la información que ha introducido, utilice R/X/F/S para seleccionar "OK" y luego pulse ENTER. Aparecerá una pantalla de confirmación de la informaci
  • Onkyo TX-NR414 | Owner Manual - Page 103
    para seleccionar "Sign In with association code". Puede ver el código de asociaci vuelva a la unidad receptor de AV y pulse ENTER. Si ya tiene Users". 2 Si no hay errores en la información que ha Channel: Añade el episodio que se está reproduciendo actualmente a Mi canal. Remove episode from My Channel
  • Onkyo TX-NR414 | Owner Manual - Page 104
    Uso de Internet Radio SN 29400992IRUS (C) Copyright 2012 ONKYO SOUND & VISION CORPORATION Japan. All rights reserved. Y1112-1 * 2 9 4 0 0 9 9 2 I R U S *
  • Onkyo TX-NR414 | Owner Manual - Page 105
    of the network services appears, and the NET indicator lights. If it flashes, verify that the Ethernet cable is firmly connected to the AV receiver. 2 Select the desired service and press ENTER. The top page of the selected service appears. Using Multiple Accounts The AV receiver supports multiple
  • Onkyo TX-NR414 | Owner Manual - Page 106
    reviews and an endless choice of personalised, ad-free radio stations, Last.fm is a great way to discover music. Pick up your free Last.fm account today at www.last.fm/join UK and Germany only: Get a subscription and you can enjoy the best of ad-free Last.fm Radio on your Onkyo AV receiver prices
  • Onkyo TX-NR414 | Owner Manual - Page 107
    , überprüfen Sie ob das Ethernet-Kabel fest im AV-Receiver eingesteckt ist. 2 Wählen Sie den gewünschten Service aus und drücken Sie ENTER. Die oberste Seite des ausgewählten Services erscheint. Verwendung mehrerer Konten Der AV-Receiver unterstützt mehrere Nutzerkonten, was bedeutet, dass Sie frei
  • Onkyo TX-NR414 | Owner Manual - Page 108
    werbefreien Last.fm-Radiosender auf Ihrem Onkyo AV-Receiver hören! Recommended Radio: Entdecken und „Neighbours" wiedergeben. Account Info: Bestätigen Sie Ihre Kontoinformation. Sign Out: gbar. Y1112-1 SN 29400992IREU (C) Copyright 2012 ONKYO SOUND & VISION CORPORATION Japan. All rights reserved.
  • Onkyo TX-NR414 | Owner Manual - Page 109
    ], [TV], and the multi zone button, remote control codes from any category can be assigned for the REMOTE MODE buttons. However, these buttons also work as input selector buttons, so choose a REMOTE MODE button that corresponds with the input to which you connect your component. For example, if you
  • Onkyo TX-NR414 | Owner Manual - Page 110
    de [RECEIVER], [TV] et du bouton multi zone, vous pouvez affecter des codes de télécommande de n'importe quelle catégorie pour les boutons REMOTE MODE. REMOTE MODE/indicador Remote parpadeará una vez despacio. Notas: • El parpadeo del mando distancia será distinto según el modelo de receptor de AV
  • Onkyo TX-NR414 | Owner Manual - Page 111
    . • Abgesehen von [RECEIVER], [TV] und der Multi-Zone-Taste, können die Fernbedienungscodes jeder Kategorie den REMOTE MODE-Tasten zugewiesen werden. REMOTE MODE-Taste/Remote-Anzeige einmal langsam. Hinweise: • Das blinkende Element auf der Fernbedienung unterscheidet sich je nach AV-Receiver-Modell
  • Onkyo TX-NR414 | Owner Manual - Page 112
    gånger. Om fjärrkontrollkoden inte ställdes in, blinkar REMOTE MODEknappen/fjärrindikatorn långsamt en gång. Anmärkningar: • Det blinkande elementet på fjärrkontrollen skiljer sig åt beroende på din modell av AV-receiver. • Fjärrkontrollen har förkonfigurerats med förvalda kanaler på fjärrkontrollen
  • Onkyo TX-NR414 | Owner Manual - Page 113
    d3&.05&.0 f ‫ء‬จj 7 d f f d f d d f d f d d f d f d f 遥控代码 Remote Control Codes 1 REMOTE MODE DISPLAY 3 REMOTE MODE Integra Remote Mode Display RECEIVER TV RECEIVER TV REMOTE MODE REMOTE MODE CD CD TV/CD （电视 /CD）]。 2 在 30 5 REMOTE MODE REMOTE MODE AV 5
  • Onkyo TX-NR414 | Owner Manual - Page 114
    Dedicated Onkyo Receiver Default 62503 Zone 2 62506 Zone 3 62507 Cable Set Top Box ADB 02254, 02769 Aon 02769 Panasonic 01982 Philips 01582, 02767 Pioneer 01877 Rogers 01877 6 Remote Control Codes Cable/PVR Combination Samsung 01877 Scientific Atlanta 01877, 01982 Shaw
  • Onkyo TX-NR414 | Owner Manual - Page 115
    , 70766 70072 70626 70626 71323 70626 70000 70868 70490, 70000 MD Yamaha Remote Control Codes 70490 Cassette Deck Aiwa Arcam Audiolab Carver Denon Grundig Harman/Kardon Inkel JVC Kenwood Magnavox Marantz Myryad Onkyo Optimus Philips Pioneer Polk Audio Radiola RCA Revox Sansui Sony Thorens Victor
  • Onkyo TX-NR414 | Owner Manual - Page 116
    Video 01998, 02802 01385 02345 02769 02378 Receiver Onkyo 52503 Satellite Set Top Box @sat Big Sat 01457 Black Diamond 01284 Blaupunkt 00173 Network 00775 Dishpro 00775 DishTV 01300 DRE 01176 Dream Multimedia 01237 DSE 02280, 02418 DSTV 00879, 00642, 01433 Remote Control Codes
  • Onkyo TX-NR414 | Owner Manual - Page 117
    , 01631 Sagem 01114 Saivod 02418 Samsung 01377, 00853, 01175, 01206, 01458, 01662, 02986 Sansui 01251 Sanyo 01626 Sat Control 01300 9 Remote Control Codes Satellite Set Top Box Sat Industrie 01611 SAT+ 01409 Satplus 01100 SatyCon 01631 Schaub Lorenz 02418 Schneider 01206
  • Onkyo TX-NR414 | Owner Manual - Page 118
    DigiQuest 01300 DirecTV 01377, 00099, 20739 Dish Network 00775 Dishpro 00775 Dream Multimedia 01237 Echostar 00775, 03099 Philips 00099 Samsung 01175, 01206, 01662 Sat Control 01300 10 Remote Control Codes SAT/PVR Combination Schneider 01206 Sedea Electronique 01206 SKY
  • Onkyo TX-NR414 | Owner Manual - Page 119
    Baur Beaumark Beijing Beko Belson Belstar Beon Berthen Bestar Bexa Black Diamond Blaupunkt Blue Sky Boca Boman Bork BPL Brandt Brimax ECE Elbe Electrograph Element Elfunk ELG Elin Elite Emerson Envision Epson Remote Control Codes 10698 10037 11667 10037, 10668 11709 10037, 10698 10037 11363
  • Onkyo TX-NR414 | Owner Manual - Page 120
    11037, 11585 10037 10171, 11423, 11564, 12049 11807, 13100, 13500 10037 10037, 10512 10556 10037 10037 10698 10037 10037 10208 10208 Remote Control Codes Television ITV JGC Jinfeng Jinxing JMB Jubilee JVC Kaisui Karcher Kathrein Kendo Kennex Kioto Kiton KLL Kneissel Koenig Kolin Kolster Konka
  • Onkyo TX-NR414 | Owner Manual - Page 121
    India Minato Minerva Ministry Of Sound Minoka Mirai Mitsubishi Mivar Onkyo Onn Onyx Opera Optimus Orbit Orion Orline Ormond Osaki Osio Osume Otto Versand Pacific Palladium Palsonic Panama Panasonic Panavision Panda Pansonic Penney Perdio Perfekt Petters Philco Philips Phocus Remote Control Codes
  • Onkyo TX-NR414 | Owner Manual - Page 122
    Sylvania Symphonic Synco Syntax Sysline Tacico Talent Tashiko Tatung TCL TCM Teac Tec Tech Line Technica Technics Technika TechniSat Technisson Techno Remote Control Codes 11610 11248 10037 10037 12001 10037 10208 10556, 10037 10178 10208 11614, 11775 10171, 11394, 11864, 11886 10171, 11394 10178
  • Onkyo TX-NR414 | Owner Manual - Page 123
    10698 10037 10650, 11576 10037 10037 10037 10037 10178, 10037, 11365, 11423, 12358 11585 10698 VCR DirecTV Go Video 20739 20614 15 VCR Humax Panasonic Philips ReplayTV Sonic Blue Sony TiVo Remote Control Codes 20739 20614, 20616 20739 20614, 20616 20614, 20616 20636 20636, 20739 PVR DirecTV Go
  • Onkyo TX-NR414 | Owner Manual - Page 124
    30713 Bel Canto Design 31571 Black Diamond 30713 Blue Parade 30571 Foehn & Hirsch Funai GE GFM Global Sphere Go Video GoldStar Goodmans GPX Grandin Grundig H & B Haaz Remote Control Codes DVD Maxim MDS Medion Memorex Metz Micromedia Micromega Microsoft Minax Mitsubishi Momitsu NAD NEC Onkyo
  • Onkyo TX-NR414 | Owner Manual - Page 125
    Magnavox Marantz Momitsu Onkyo Oppo Panasonic Philips 32250, 32474, 32652 33052 Remote Control Codes Blu-ray Disc Sony Sylvania Toshiba Vizio Yamaha 31516, 32180 30675 32551, 32705, 33157 32563 32298, 32299 DVD-R Accurian Aristona Denon Emerson Funai Go Video
  • Onkyo TX-NR414 | Owner Manual - Page 126
    31597 30646 30741 HD-DVD Integra LG Microsoft Onkyo Xbox 32901, 33104 33504 30741 32083 32901, 33104 33504 32083 TV/DVD Combination Akai 11675 Black Diamond 11037, 30713 Blue Sky 11037, 30713 Universum 30713 Vestel 11037 Viewsonic 12049 Weltstar 11037, 30713 18 Remote Control Codes
  • Onkyo TX-NR414 | Owner Manual - Page 127
    Memo Remote Control Codes 19
  • Onkyo TX-NR414 | Owner Manual - Page 128
    SN 29401094 (C) Copyright 2012 ONKYO SOUND & VISION CORPORATION Japan. All rights reserved. Y1112-1 * 2 9 4 0 1 0 9 4 *
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
E
n
AV RECEIVER
TX-NR414
Instruction Manual
Contents
Safety Information and Introduction
............
2
Table of Contents
...........................................
6
Connections
.................................................
12
Turning On & Basic Operations
..................
19
Advanced Operations
..................................
39
Controlling Other Components
...................
53
Appendix
.......................................................
59
Internet Radio Guide
Remote Control Codes