Onkyo TX-NR777 THX-Certified 7.2 Channel Network A/V Receiver Owners Manual -A - Page 58

Miscellaneous, Tuner, Remote ID, Firmware Update, Initial Setup, Enable: Notify updates

Get Onkyo TX-NR777 THX-Certified 7.2 Channel Network A/V Receiver PDF manuals and user guides View all Onkyo TX-NR777 THX-Certified 7.2 Channel Network A/V Receiver manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

>>Specifications >>Advanced Setup >>Listening Modes >>Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. 7. Miscellaneous Change the frequency step for the tuner, update the firmware, and perform Initial Setup, etc. ˙ 1. Tuner Setting Item AM / FM Frequency Step Default Value Setting Details 10 kHz / 0.2 MHz Select a frequency step depending on your area of residence. Select "10 kHz/0.2 MHz" or "9 kHz/0.05 MHz". • When this setting is changed, all radio presets are deleted. ˙ 2. Remote ID Setting Item Remote ID Default Value 1 Setting Details Select an ID for the unit's remote controller from "1", "2", and "3" to prevent interference between the unit and other ONKYO components that are installed in the same room. After changing the ID on the main unit, change the ID on the remote controller accordingly with the following procedure. While holding down MODE, press the following buttons for about 3 seconds. • To change the remote controller ID to "1": (The remote indicator flashes once.) • To change the remote controller ID to "2": (The remote indicator flashes twice.) • To change the remote controller ID to "3": (The remote indicator flashes three times.) ˙ 3. Firmware Update Setting Item Update Notice Version Update via NET Update via USB Default Value Enable    Setting Details Availability of a firmware update will be notified via network. "Enable": Notify updates "Disable": Disable notifications The current firmware version will be displayed. Press ENTER to select when you want to update the firmware via network. • You will not be able to select this setting if you do not have Internet access or there is nothing to update. Press ENTER to select when you want to update the firmware via USB. • You will not be able to select this setting if a USB storage device is not connected or there is nothing to update in the USB storage device. • Wait for a while if "Firmware Update" cannot be selected. It will appear when the network feature is started. ˙ 4. Initial Setup You can make the initial setup from the setup menu. • Wait for a while if "Initial Setup" cannot be selected. It will appear when the network feature is started. ˙ 5. Lock Setting Item Default Value Setup Parameter Unlocked Setting Details Lock the Setup menu to protect the settings. "Locked": The menu is locked. "Unlocked": The menu is unlocked. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
25
> Network Functions
> Specifications
> Advanced Setup
> Listening Modes
Troubleshooting
Supplementary Information, etc.
|
> Basic Manual
7. Miscellaneous
Change the frequency step for the tuner, update the firmware, and perform Initial Setup,
etc.
■
1. Tuner
Setting Item
Default Value
Setting Details
AM / FM
Frequency Step
10 kHz / 0.2 MHz
Select a frequency step depending on your area of
residence.
Select "10 kHz/0.2 MHz" or "9 kHz/0.05 MHz".
•
When this setting is changed, all radio presets
are deleted.
■
2. Remote ID
Setting Item
Default Value
Setting Details
Remote ID
1
Select an ID for the unit's remote controller from
"1", "2", and "3" to prevent interference between
the unit and other ONKYO components that are
installed in the same room. After changing the ID
on the main unit, change the ID on the remote
controller accordingly with the following procedure.
While holding down MODE, press the following
buttons for about 3 seconds.
•
To change the remote controller ID to "1":
(The remote indicator flashes once.)
•
To change the remote controller ID to "2":
(The remote indicator flashes twice.)
•
To change the remote controller ID to "3":
(The remote indicator flashes three times.)
■
3. Firmware Update
Setting Item
Default Value
Setting Details
Update Notice
Enable
Availability of a firmware update will be notified via
network.
"Enable": Notify updates
"Disable": Disable notifications
Version
-
The current firmware version will be displayed.
Update via
NET
-
Press ENTER to select when you want to update
the firmware via network.
•
You will not be able to select this setting if you
do not have Internet access or there is nothing
to update.
Update via
USB
-
Press ENTER to select when you want to update
the firmware via USB.
•
You will not be able to select this setting if a
USB storage device is not connected or there is
nothing to update in the USB storage device.
•
Wait for a while if "Firmware Update" cannot be selected. It will appear when the network feature is
started.
■
4. Initial Setup
You can make the initial setup from the setup menu.
•
Wait for a while if "Initial Setup" cannot be selected. It will appear when the network
feature is started.
■
5. Lock
Setting Item
Default Value
Setting Details
Setup Parameter
Unlocked
Lock the Setup menu to protect the settings.
"Locked": The menu is locked.
"Unlocked": The menu is unlocked.