Onkyo TX-RZ610 7.2 Channel Network A/V Receiver Owners Manual - English/Spanis - Page 9

Step2: Connect the Speakers

Get Onkyo TX-RZ610 7.2 Channel Network A/V Receiver PDF manuals and user guides View all Onkyo TX-RZ610 7.2 Channel Network A/V Receiver manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

> Before start > Hookup > Setup > Playback > Part Names Step2: Connect the Speakers 1/2˝ (12 mm) 1 in case of: Pages 3 to 7 En Connect 123456 for a 5.1-channel system. For a 7.1-channel system, select either surround back speakers or height speakers, and connect 78. Up to two powered subwoofers can be connected. The same signal is output from each of the SUBWOOFER jacks. Setup 0 The speaker configuration is set to 12345678 audio output by default. If there are speakers you won't be connecting, you need to change the settings in Initial Setup, "1. AccuEQ Room Calibration" (ÄP18) so that the audio from those speakers you are not connecting is sent to other speakers. Make sure the exposed wires of the speakers do not stick out of the speaker terminals when connecting. If the exposed wires of the speakers touch the rear panel or the + and - wires touch each 2 other, the protection circuit will be activated. 1 Speaker cable, 2 Subwoofer cable 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
En
9
> Before start
> Hookup
> Setup
> Playback
> Part Names
Step2: Connect the Speakers
2
1
1/2˝
(12 mm)
1
Speaker cable,
2
Subwoofer cable
in case of:
Pages 3 to 7
Connect
123456
for a 5.1-channel system. For a
7.1-channel system, select either surround back speakers
or height speakers, and connect
78
. Up to two powered
subwoofers can be connected. The same signal is output
from each of the SUBWOOFER jacks.
Make sure the exposed wires of the speakers do not stick out of
the speaker terminals when connecting. If the exposed wires of
the speakers touch the rear panel or the + and – wires touch each
other, the protection circuit will be activated.
Setup
0
The speaker configuration is set to
123456
78
audio output by default. If there
are speakers you won't be connecting, you need to
change the settings in Initial Setup, "1. AccuEQ
Room Calibration" (
Ä
P18) so that the audio from
those speakers you are not connecting is sent to
other speakers.