Onkyo TX-SR3100 TX -SR Manual - Page 60

Crossover

Get Onkyo TX-SR3100 PDF manuals and user guides View all Onkyo TX-SR3100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

2. Speaker „ 2. Crossover Set what number of Hz in the low frequency range is output from each speaker and what should be output from the subwoofer. When a subwoofer is not to be used, set to "Full Band" so that the bass is output from the speakers. ‰ Crossover Type (Default Value: Normal) Set the crossover frequency to suit the speakers. Klipsch Normal When Klipsch speakers are used. The crossover that is optimum for the speakers selected in Speaker Combo ( →p62) is applied. In this case, the crossover for each speaker cannot be changed. When other than Klipsch speakers are used Front Center Height Surround LPF of LFE Double Bass (Default Value: 100 Hz) (Default Value: 100 Hz) (Default Value: 100 Hz) (Default Value: 100 Hz) (Default Value: 120 Hz) (Default Value: On) Front: Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • If "Configuration" - "Subwoofer" is set to "No", "Front" is fixed to "Full Band", and the low pitched range of the other channels is output from the front speakers. Refer to the instruction manual of your speakers to make the setting. Setup Center, Height, Surround: Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • "Full Band" can be selected only when "Front" is set to "Full Band". • If the item cannot be selected even though connection is correct, check if the setting in "Configuration" - "Speaker Channels" matches the number of connected channels. LPF of LFE: Set the low-pass filter for LFE (low-frequency effect) signals in order to pass only the lower frequency signals than the set value, and thus cancel unwanted noises. The low-pass filter is effective only on sources with LFE channel. The value from "80 Hz" to "120 Hz" can be set. "Off": When this function is not used Double Bass: This can only be selected when the setting for "Configuration" - "Subwoofer" is "Yes", and the "Front" setting is "Full Band". Boost bass output by feeding bass sounds from the front left and right speakers and the center speaker to the subwoofer. "On": Bass output is boosted. "Off": Bass output is not boosted. • This function is not automatically set even if AccuEQ Room Calibration is performed. 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
60
Setup
2. Speaker
±
2. Crossover
Set what number of Hz in the low frequency range is output from each speaker
and what should be output from the subwoofer. When a subwoofer is not to be
used, set to "Full Band" so that the bass is output from the speakers.
±
Crossover Type (Default Value: Normal)
Set the crossover frequency to suit the speakers.
Klipsch
When Klipsch speakers are used. The crossover that is
optimum for the speakers selected in Speaker Combo
(
→
p62
) is applied. In this case, the crossover for each
speaker cannot be changed.
Normal
When other than Klipsch speakers are used
Front
(Default Value: 100 Hz)
Center
(Default Value: 100 Hz)
Height
(Default Value: 100 Hz)
Surround
(Default Value: 100 Hz)
LPF of LFE
(Default Value: 120 Hz)
Double Bass
(Default Value: On)
Front:
Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting
frequencies for each channel.
"Full Band": Full band will be output.
•
If "Con±guration" - "Subwoofer" is set to "No", "²ront" is ±xed to "²ull Band",
and the low pitched range of the other channels is output from the front
speakers. Refer to the instruction manual of your speakers to make the
setting.
Center, Height, Surround:
Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting
frequencies for each channel.
"Full Band": Full band will be output.
• "Full Band" can be selected only when "Front" is set to "Full Band".
• If the item cannot be selected even though connection is correct, check if
the setting in "Con±guration" - "Speaker Channels" matches the number of
connected channels.
LPF of LFE:
Set the low-pass ±lter for L²E (low-frequency eFect) signals in order to pass
only the lower frequency signals than the set value, and thus cancel unwanted
noises. The low-pass ±lter is eFective only on sources with L²E channel.
The value from "80 Hz" to "120 Hz" can be set.
"OF": When this function is not used
Double Bass:
This can only be selected when the setting for "Con±guration" - "Subwoofer" is
"Yes", and the "Front" setting is "Full Band".
Boost bass output by feeding bass sounds from the front left and right
speakers and the center speaker to the subwoofer.
"On": Bass output is boosted.
"OF": Bass output is not boosted.
• This function is not automatically set even if AccuEQ Room Calibration is
performed.