Optoma EH1020 User's Manual - Page 13

Powering the projector On / Off - projector lamp

Get Optoma EH1020 PDF manuals and user guides
UPC - 796435411503
View all Optoma EH1020 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Installation Powering the projector On / Off Powering On the Projector . Remove the lens cap.  2. Securely connect the power cord and signal cable. When connected, the ON/STANDBY LED will turn Amber. 3. Turn on the lamp by pressing " " button either on the top of  (*) When Power mode (Standby) is set to Eco., the projector or on the remote. The ON/STANDBY LED will now turn Green.  The startup screen will display in approximately 0 seconds. the VGA & Audio The first time you use the projector, you will be asked to pass-through and RS-232 will be select the preferred language and power saving mode.(*) deactivated when the projector is in 4. Turn on and connect the source that you want to display standby. on the screen (computer, notebook, video player, etc). The projector will detect the source automatically. If not, push menu button and go to "OPTIONS". Make sure that the "Source Lock" has been set to "Off".  If you connect multiple sources at the same time, press the "SOURCE" button on the control panel or direct source keys on the remote control to switch between inputs. 2 Power ? POWER ? POWER  Turn on the projector first and then select the signal sources.  Lens Cap 3 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
±3
English
Installation
Powering the projector On / Off
Turn on the
projector first and
then select the
signal sources.
Powering On the Projector
±. Remove the lens cap.
2. Securely connect the power cord and signal cable. When
connected, the ON/STANDBY LED will turn Amber.
3. Turn on the lamp by pressing “
” button either on the top of
the projector or on the remote. The ON/STANDBY LED will
now turn Green.
The startup screen will display in approximately ±0 seconds.
The first time you use the projector, you will be asked to
select the preferred language and power saving mode.(*)
4. Turn on and connect the source that you want to display
on the screen (computer, notebook, video player, etc). The
projector will detect the source automatically. If not, push
menu button and go to “OPTIONS”.
Make sure that the “Source Lock” has been set to “Off”.
If you connect multiple sources at the same time, press the
“SOURCE” button on the control panel or direct source keys
on the remote control to switch between inputs.
POWER
?
Lens Cap
±
Power
2
(*) When Power
mode (Standby)
is set to Eco.,
the VGA & Audio
pass-through and
RS-232 will be
deactivated when
the projector is in
standby.