Optoma EH512 EH512 User Manual - Page 55

Replacing the lamp continued, Lamp Reset: i Press Menu

Get Optoma EH512 PDF manuals and user guides View all Optoma EH512 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

MAINTENANCE Replacing the lamp (continued) 2 1 3 4 5 6 Procedure: 1. Switch off the power to the projector by pressing the " " button on the projector keypad or the remote control. 2. Allow the projector to cool down for at least 30 minutes. 3. Disconnect the power cord. 4. Remove the dust filter. 1 5. First slide and then lift the top cover. 2 6. Unscrew the screw on the side panel. 3 7. Lift up the lamp handle. 4 8. Remove the lamp cord. 5 9. Remove the lamp module carefully. 6 10. To replace the lamp module, reverse the previous steps. 11. Turn on the projector and reset the lamp timer. 12. Lamp Reset: (i) Press "Menu"  (ii) Select "Setup"  (iii) Select "Lamp Settings"  (iv) Select "Lamp Reset"  (v) Select "Yes". Note: ‡‡ ‡‡ The projector cannot be turned on if the lamp cover has not been placed back on the projector. Do not touch the glass area of the lamp. Hand oil can cause the lamp shatter. Use a dry cloth to clean the lamp module if it was accidentally touched. English 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
English
55
MAINTENANCE
Replacing the lamp (continued)
4
6
5
2
1
3
Procedure:
1.
Switch off the power to the projector by pressing the “
” button on the projector keypad or the remote
control.
2.
Allow the projector to cool down for at least 30 minutes.
3.
Disconnect the power cord.
4.
Remove the dust filter.
1
5.
First slide and then lift the top cover.
2
6.
Unscrew the screw on the side panel.
3
7.
Lift up the lamp handle.
4
8.
Remove the lamp cord.
5
9.
Remove the lamp module carefully.
6
10.
To replace the lamp module, reverse the previous steps.
11.
Turn on the projector and reset the lamp timer.
12.
Lamp Reset: (i) Press “Menu”
(ii) Select “Setup”
(iii) Select “Lamp Settings”
(iv) Select “Lamp
Reset”
(v) Select “Yes”.
Note°
±
The projector cannot be turned on if the lamp cover has not been placed back on the projector.
±
Do not touch the glass area of the lamp. Hand oil can cause the lamp shatter. Use a dry cloth to clean
the lamp module if it was accidentally touched.