Optoma S316 User Manual - Page 50

Blurry double image, Two images, side-by-side format, Image does not display in 3D

Get Optoma S316 PDF manuals and user guides View all Optoma S316 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Appendices The projector stops responding to all controls  If possible, turn off the projector, then unplug the power cord and wait at least 60 seconds before reconnecting power.  Check that "Keypad Lock" is not activated by trying to control the projector with the remote control. Blurry double image  Press "3D Format" button and switch to "Off" to avoid normal 2D image is blurry double image. Two images, side-by-side format  Press "3D Format" button and switch to "SBS" for input signal is HDMI 1.3 2D 1080i side-by-side. Image does not display in 3D  Check if the battery of 3D glasses is drained.  Check if the 3D glasses is turned on.  When the input signal is HDMI 1.3 2D (1080i side-by-side half), press "3D Format" button and switch to "SBS". Lamp burns out or makes a popping sound  When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section on pages 53-54. English 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
50
English
Appendices
The projector stops responding to all controls
If p
ossible, turn off the projector, then unplug the power cord and
wait at least 60 seconds before reconnecting power.
Check that “Keypad Lock” is not activated by trying to control the
projector with the remote control.
Blurry double image
Press “3D Format” button and switch to “Off” to avoid normal 2D
image is blurry double image.
Two images, side-by-side format
Press “3D Format” button and switch to “SBS” for input signal is
HDMI 1.3 2D 1080i side-by-side.
Image does not display in 3D
Check if the battery of 3D glasses is drained.
Check if the 3D glasses is turned on.
When the input signal is HDMI 1.3 2D (1080i side-by-side half),
press “3D Format” button and switch to “SBS”.
Lamp burns out or makes a popping sound
When the lamp reaches its end of life, it will burn out and may
make a loud popping sound. If this happens, the projector will not
turn on until the lamp module has been replaced. To replace the
lamp, follow the procedures in the “Replacing the Lamp” section on
pages 53-54.