Optoma TX1080 User's Manual - Page 50

Replacing the lamp - bulb

Get Optoma TX1080 PDF manuals and user guides
UPC - 796435111465
View all Optoma TX1080 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Appendices Replacing the lamp The projector automatically detects the lamp life. When the lamp life is nearing the end of use, you will receive a warning message. When you see this message, please contact your local reseller or Warning: Lamp com- service center to change the lamp as soon as possible. Make sure partment is hot! Allow the projector has been cooled down for at least 30 minutes before it to cool down before changing the lamp. changing lamp! 1 3 2 4 Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped. Lamp Replacing Procedure: 1. Switch off the power to the projector by pressing the Power button. 2. Allow the projector to cool down at least 30 minutes. 3. Disconnect the power cord. 4. Use a screwdriver to remove the screw from the cover. 5. Push up and remove the cover. 6. Remove the 2 screws from the lamp module. 7. Pull out the lamp module.  To replace the lamp module, reverse the previous steps. 8. Turn on the projector and do "Lamp Reset" after the lamp module is replaced. Lamp Reset: (i)Press "Menu" -> (ii)Select "Options" -> (iii)Select "Lamp Settings" ->(iv)Select "Lamp Reset" -> (v)Select "Yes". 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
µ0
Appendices
Replacing the lamp
The projector automatically detects the lamp life.
When the lamp
life is nearing the end of use, you will receive a warning message.
When you see this message, please contact your local reseller or
service center to change the lamp as soon as possible. Make sure
the projector has been cooled down for at least 30 minutes before
changing the lamp.
Warning: Lamp com
-
partment is hot! Allow
it to cool down before
changing lamp!
Warning: To reduce the
risk of personal injury,
do not drop the lamp
module or touch the
lamp bulb. The bulb
may shatter and cause
injury if it is dropped.
2
4
Lamp Replacing Procedure:
1.
Switch off the power to the projector by pressing the Power
button.
2.
Allow the projector to cool down at least 30 minutes.
3.
Disconnect the power cord.
4.
Use a screwdriver to remove the screw from the cover.
5.
Push up and remove the cover.
6.
Remove the 2 screws from the lamp module.
7.
Pull out the lamp module.
To replace the lamp module, reverse the previous steps.
8.
Turn on the projector and do “Lamp Reset” after the lamp
module is replaced.
Lamp Reset: (i)Press “Menu” -> (ii)Select “Options” ->
(iii)Select “Lamp Settings” ->(iv)Select “Lamp Reset” ->
(v)Select “Yes”.
1
3