Optoma ZH403 HZ39HDR UM - Page 21

USING THE PROJECTOR, Powering on / off the projector

Get Optoma ZH403 PDF manuals and user guides View all Optoma ZH403 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

USING THE PROJECTOR Powering on / off the projector or Power Switch Freeze L R Enter Page- Laser Page+ Keystone -+ Volume -+ 1 4 HDMI 7 User1 Source 2 Menu 5 VGA 8 User2 0 3 3D 6 Video 9 User3 Resync Powering on 1. Securely connect the power lead and signal/source cable. When connected, the Power LED will turn red. 2. Turn on the projector by pressing the button on the projector keypad or remote control. 3. A start up screen will display in approximately 10 seconds and the Power LED will be flashing blue. Note: The first time the projector is turned on, you will be prompted to select the preferred language, projection orientation, and other settings. Powering off 1. Turn off the projector by pressing the button on the projector keypad or remote control. 2. The following message will be displayed: Power Off Press power key again. 3. Press the button again to confirm, otherwise the message will disappear after 15 seconds. When you press the button for the second time, the projector will shut down. 4. The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the Power LED will flash blue. When the Power LED turns solid red, this indicates the projector has entered standby mode. If you wish to turn the projector back on, you must wait until the cooling cycle has finished and the projector has entered standby mode. When the projector is in standby mode, simply press the button again to turn on the projector. 5. Disconnect the power lead from the electrical outlet and the projector. Note: It is not recommended that the projector is turned on immediately, right after a power off procedure. English 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
English
21
USING THE PROJECTOR
Powering on / off the projector
Freeze
Power
Switch
L
R
or
Powering on
1.
Securely connect the power lead and signal/source cable. When connected, the Power LED will turn
red.
2.
Turn on the projector by pressing the
button on the projector keypad or remote control.
3.
A start up screen will display in approximately 10 seconds and the Power LED will be flashing blue.
Note:
The first time the projector is turned on, you will be prompted to select the preferred language, projection
orientation, and other settings.
Powering off
1.
Turn off the projector by pressing the
button on the projector keypad or remote control.
2.
The following message will be displayed:
Power Off
Press power key again.
3.
Press the
button again to confirm, otherwise the message will disappear after 15 seconds. When
you press the
button for the second time, the projector will shut down.
4.
The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the Power
LED will flash blue. When the Power LED turns solid red, this indicates the projector has entered
standby mode. If you wish to turn the projector back on, you must wait until the cooling cycle has
finished and the projector has entered standby mode. When the projector is in standby mode, simply
press the
button again to turn on the projector.
5.
Disconnect the power lead from the electrical outlet and the projector.
Note:
It is not recommended that the projector is turned on immediately, right after a power off procedure.