Optoma ZH606-B 606 User Manual - Page 20

Powering on / off the projector

Get Optoma ZH606-B PDF manuals and user guides View all Optoma ZH606-B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

USING THE PROJECTOR Powering on / off the projector or On Off Geometric Correction PIP/PBP F1 Mode F2 AV Mute ENTER Info. Source Re-Sync F3 Volume D Zoom Menu Format Freeze Remote ID All Powering on Lens cap VGA S-Video HDMI1 HDMI2 123 HDBaseT Video DVI HDMI3 456 BNC YPbPr DisplayPort 3D 7890 1. Remove the lens cap. 2. Securely connect the power lead and signal/source cable. When connected, the Power LED will turn red. 3. Turn on the projector by pressing the button on the projector keypad or remote control. 4. A start up screen will display in approximately 10 seconds and the Power LED will be flashing blue or flashing green. Note: The first time the projector is turned on, you will be prompted to select the preferred language, projection orientation, and other settings. Powering off 1. Turn off the projector by pressing the button on the projector keypad or the control. 2. The following message will be displayed: button on the remote Power Off Press power key again. 3. Press the or button again to confirm, otherwise the message will disappear after 15 seconds. When you press the or button for the second time, the projector will shut down. 4. When the Power turns solid red, this indicates the projector has entered standby mode. If you wish to turn the projector back on, you must wait until the cooling cycle has finished and the projector has entered standby mode. When the projector is in standby mode, simply press the button again to turn on the projector. 5. Disconnect the power lead from the electrical outlet and the projector. Note: It is not recommended that the projector is turned on immediately, right after a power off procedure. 20 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
English
20
USING THE PROJECTOR
Powering on / off the projector
On
Geometric
Correction
PIP/PBP
Off
F1
F2
or
Lens cap
Powering on
1.
Remove the lens cap.
2.
Securely connect the power lead and signal/source cable. When connected, the Power LED will turn
red.
3.
Turn on the projector by pressing the
button on the projector keypad or remote control.
4.
A start up screen will display in approximately 10 seconds and the Power LED will be flashing blue or
flashing green.
Note:
The first time the projector is turned on, you will be prompted to select the preferred language, projection
orientation, and other settings.
Powering off
1.
Turn off the projector by pressing the
button on the projector keypad or the
button on the remote
control.
2.
The following message will be displayed:
Power Off
Press power key again.
3.
Press the
or
button again to confirm, otherwise the message will disappear after 15 seconds.
When you press the
or
button for the second time, the projector will shut down.
4.
When the Power turns solid red, this indicates the projector has entered standby mode. If you wish
to turn the projector back on, you must wait until the cooling cycle has finished and the projector has
entered standby mode. When the projector is in standby mode, simply press the
button again to
turn on the projector.
5.
Disconnect the power lead from the electrical outlet and the projector.
Note:
It is not recommended that the projector is turned on immediately, right after a power off procedure.