Home » Optoma Manuals » Projectors » Optoma ZW300USTI » Manual Viewer

Optoma ZW300USTI TouchBeam Interactive User Manual - Page 26

Step 6: Touch Area Setting

Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Step 6: Touch Area Setting A. Select Auto Touch Area Setting: Note: • Quit all software applications • Reduce ambient light (dim) • Do not obstruct or shake lens during Touch Area Setting • Check if projection image is clear. If not, adjust focus to sharpen the image If failure message appears, please switch to Manual Touch Area Setting. B. Select Manual Touch Area Setting: 31

Section	Page
User manual	1
User manual	1
Table of contents	2
Table of contents	2
Usage Notice	3
Usage Notice	3
Precautions	3
Precautions	3
How it works	3
How it works	3
Package Overview	4
Package Overview	4
Before Installation - Environment Check	5
Before Installation - Environment Check	5
Note:	5
Note:	5
TouchBeam installation information	6
TouchBeam installation information	6
Whiteboard Setup for Frames 0.12” (3mm) or smaller	7
Whiteboard Setup for Frames 0.12” (3mm) or smaller	7
Whiteboard Setup for Aluminum Frames larger than 0.12” (3mm)	8
Whiteboard Setup for Aluminum Frames larger than 0.12” (3mm)	8
Notes	9
Notes	9
Measuring projection surface flatness	11
Measuring projection surface flatness	11
Installation guide	12
Installation guide	12
Installation workflow	12
Installation workflow	12
Installing the whiteboard	15
Installing the whiteboard	15
Installing the TouchBeam module	16
Installing the TouchBeam module	16
Step 1: Mounting the TouchBeam module	16
Step 1: Mounting the TouchBeam module	16
1.3a Short-term installation (few days to a few weeks):	16
1.3a Short-term installation (few days to a few weeks):	16
1.3 3b Long-term use:	18
1.3 3b Long-term use:	18
1.4 Attach the module to the bracket with screws	18
1.4 Attach the module to the bracket with screws	18
Step 2: Install TouchBEAM Utility Software	19
Step 2: Install TouchBEAM Utility Software	19
1. System requirements	19
1. System requirements	19
Step 3: Initial Setup	20
Step 3: Initial Setup	20
Step 4: Operation Mode	21
Step 4: Operation Mode	21
Step 5: TouchBeam Alignment	22
Step 5: TouchBeam Alignment	22
Step 6: Touch Area Setting	26
Step 6: Touch Area Setting	26
Note:	26
Note:	26
Step 7: Calibration	28
Step 7: Calibration	28
Note:	28
Note:	28
Note:	28
Note:	28
Step 8: Touch Sensitivity	29
Step 8: Touch Sensitivity	29
Step 9: Trouble-shooting Viewer	30
Step 9: Trouble-shooting Viewer	30
Appendix	31
Appendix	31
Troubleshooting	31
Troubleshooting	31
Q2 What to do when Windows system cannot identify the USB device?	31
Q2 What to do when Windows system cannot identify the USB device?	31
Q3 Why is the utility icon ( ) red and not green ( / )?	32
Q3 Why is the utility icon ( ) red and not green ( / )?	32
Q4 What to do when there is only single touch point?	32
Q4 What to do when there is only single touch point?	32
Q5 When should Calibration and Touch Area Setting be completed?	33
Q5 When should Calibration and Touch Area Setting be completed?	33
Q6 What to do when Auto Calibration and Auto Touch Area Setting both fail?	33
Q6 What to do when Auto Calibration and Auto Touch Area Setting both fail?	33
Q8 What to do when the mouse cursor ( ) flashes or jumps on screen, or when the Touch function does not work well for a certain projection area?	34
Q8 What to do when the mouse cursor ( ) flashes or jumps on screen, or when the Touch function does not work well for a certain projection area?	34
Q9 What to do when the projection area corner is insensitive or intermittent lines are observed? A:	34
Q9 What to do when the projection area corner is insensitive or intermittent lines are observed? A:	34
Q10 What to do when the touch function is not accurate?	35
Q10 What to do when the touch function is not accurate?	35
Appendix	36
Appendix	36
Interactive cable layout	36
Interactive cable layout	36
Distance calculator	37
Distance calculator	37
XGA	37
XGA	37
1080p	38
1080p	38
Specification	39