Oreck U4140 Owners Guide - Page 5

ENGLISH Parts List To assist you in identifying components of your vacuum, the parts have been numbered as follows: 10 1 Handle section, upper 2 Tube, lower 3 Power head 4 Outer bag 5 Paper filter dust bag 6 Power cord 7 Retaining spring 8 Bag tension bar 5 9 Zip fastener 10 On/off switch 11 Cord clamp 12 Plastic loop/cable clamp 13 Connector assembly 14 Fan housing 15 Cord assembly 91 11 12 13 4 2 6 87 14 15 3 Assembly fig. 1 Before assembling appliance, remove two screws from the connector assembly. Remove cardboard insert by pulling upward. fig. 2 With ON/OFF switch facing the front of the unit, slide upper handle section over matching section of the connector assembly. Insert short screw into top hole and long screw into the bottom hole then tighten firmly until handle is no longer loose. fig. 3 Attach cord to cord clip by pressing cord above and below clip ensuring the cord is fully rested in clip. Operating Instructions Make sure disposable paper filter dust bag is in place. DO NOT operate the cleaner without a paper filter dust bag. Plug the power cord into an electrical outlet and press the On Low (l) - On High (ll) - OFF(O) switch on handle assembly when ready to operate. Up-Position Lock fig. 4 Place foot on power head and lean handle back gently to release lock for vacuum use. Return handle to the full upright position to engage lock. NOTE: Do not operate the unit while in the upright and locked position. Do not let the unit run while in any one stationary position for any period of time. Keep the unit moving while in operation. For Easy Power Cord Storage fig. 5 Wrap power cord around cord hook on handle and cord hook on connector. Secure to "U" shaped part on plug. Operating Recommendations This new ORECK XL High-Speed Upright is one of the finest, fastest, and strongest units in its class. You'll love the way it cleans, gets under things, and it's SO lightweight and easy to use. The following are a few simple suggestions regarding its operation: 1. When inserting a new disposable paper filter dust bag-FIRST PUFF OUT and OPEN THE BAG. 2. When the disposable filter dust bag is full, REPLACE IT. 3. If at any time the machine does not pick up properly or makes an unusual noise, STOP OPERATION and service. 4. Although your upright will pick up pins, paper clips, and other small objects, it is recommended that these be removed from the floor before you vacuum. Failure to do so may result in permanent damage to the motor suction fan and its housing. 4 5. WARNING: Do not use your vacuum cleaner on damp or wet surfaces. This will cause damage to the vacuum cleaner and is dangerous to the user. Damage caused by use on wet or damp surfaces is not covered under warranty. 6. REPLACE THE BELT EVERY 6 MONTHS. 7. Change the disposable filter dust bag at least once a month- even if it is not full! The collected dust in the dust bag can cause odor, attract moisture, and can affect the efficiency of the cleaner. 8. DO NOT run the vacuum cleaner over the cord. The revolving brush could damage the cord. 9. Use caution when vacuuming over area rug edges & fringe. General Information The performance of your new cleaner greatly depends upon care and maintenance. The instructions in this manual will guide you in performing basic care and maintenance. To obtain the most satisfying years of service read the instructions and keep them handy for future reference. Disposable Paper Filter Dust Bags Disposable paper filter dust bags play a very important role in the efficiency of your ORECK vacuum cleaner. The purpose of the filter bag is to trap dirt, but at the same time it must be porous enough to allow air to pass through. If the filter bag becomes clogged, no air can pass through the cleaner and cleaning cannot take place, regardless of the cleaner's power. To keep your cleaner operating at maximum efficiency, change the dust bag frequently. DO NOT FILL ABOVE THE LINE INDICATED ON THE DUST BAG. Be sure the disposable paper filter dust bag is installed properly. All paper dust bags are not the same. Your ORECK disposable dust bags have been designed to be used with the ORECK cleaner. Using bags other than genuine ORECK TYPE CC disposable bags will affect the cleaning ability of your cleaner and could cause damage to it. The Belt The belt on your vacuum cleaner controls the speed of the revolving brush and is very important for the effective operation of the cleaner. If the belt becomes stretched or cut, it will cause the revolving brush to stop completely or slow down. See instructions in the manual for replacing belt. An extra belt is stored in the baseplate of your cleaner. When buying replacement belts, use ONLY ORECK genuine belts. Belts other than Oreck belts will not operate the revolving brush correctly and may create undue stress which will cause damage to the motor and brush bearings. Using belts other than ORECK belts will void the warranty. Lubrication The vacuum cleaner motor bearings are factory lubricated and sealed. Further lubrication is not required. General Cleaner Care At least once a month, check for and remove excessive lint, string or hair from revolving brush. Wipe the outside of the cleaner with a damp cloth. Also clean the connector deflector assembly area, base of cleaner and fan housing area. If there is dust in the outer bag, vacuum it or shake it out. A little preventative maintenance will keep your cleaner looking new and will ensure continued cleaning effectiveness.