Oregon Scientific SE138 User Manual - Page 1
Oregon Scientific SE138 Manual
View all Oregon Scientific SE138 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
STRAPLESS HEART RATE MONITOR Model: SE138 USER MANUAL EN INTRODUCTION Thank you for selecting the Oregon ScientificTM Strapless Heart Rate Monitor (SE138). The SE138 is a very practical sports and fitness aid as it monitors your heart rate without requiring to wear a heart rate transmitter. It is equipped with calorie measurement along with real-time clock, stopwatch, backlight and keypad lock functions. CONTROL BUTTONS 6 3 1 4 2 5 7 1. -: Toggle between setting sub-modes; decrease values 2. MODE: Toggle between modes, confirm and exit settings 3. ST/SP/+: Start / stop stopwatch; toggle between setting sub-modes; increase values 4. / : Activate backlight; lock keypad 5. SET/RST: Enter setting sub-mode; confirm setting; reset stopwatch and calorie values 6. Top metallic plate: Touch to enter Heart Rate Mode and take heart rate measurement 7. Bottom metallic plate: Touch to enter Heart Rate Mode and take heart rate measurement LCD 1 11 2 12 3 4 13 14 5 15 16 6 17 7 8 18 9 10 1. : Indicates you are in Stopwatch Mode or the stopwatch is running 2. : Indicates alarm is On 3. : Smart indicator to decrease values 4. : Smart indicator to toggle between setting sub-modes 5. Displays stopwatch, date or mode banners 6. : Indicates a heart rate reading is detected 7. : 12 hour clock 8. : Smart indicator to quick exit and return to previous mode 9. : Calorie unit 10. : Weight unit 11. : Indicates you are in setting sub-modes 12. : Indicates beep tone is Off 13. : Smart indicator to increase values 14. : Smart indicator to toggle between setting submodes 15. : Indicates keypad is locked 16. or : Indicates battery power is low 17. Displays time or calorie reading 18. : Smart indicator to confirm setting and move to the next setting GETTING STARTED ACTIVATE WATCH (FIRST TIME USE ONLY) Press and hold any key until the screen is activated. SET TIME AND USER DATA To effectively use the watch for calculating calorie burned (based on the user's age, weight, heart rate reading and exercise time), you are advised to set the time and your personal data in Set Up Mode. Refer to "Time Setting Mode" and "User Data Setting Mode" in Set Up Mode. IMPORTANT Remember to set the time and user data after every battery replacement or power reset. BATTERY REPLACEMENT The watch uses a CR2032 3V battery, which has already been installed. If or flashes, it means battery power is low and should be replaced. If battery power is low, alarm beeping, backlight and heart rate measuring functions will be disabled. 1. Use a small Phillips screwdriver to remove battery compartment lid. Once opened, please keep the screws in a safe place to avoid losing them. 2. Remove the old battery and insert the new one matching the polarities. 3. Replace the lid by screwing it back into place. HEART RATE MEASUREMENT You can measure your heart rate anytime (except in setting sub-modes). 1. Wear the watch on your wrist and place fingertips (suggest to use index finger and middle finger) on both metallic plates to enter Heart Rate Mode. A beep tone will be heard and "HR" banner will flash to indicate the watch is detecting heart rate reading. It will take between 6-10 seconds to detect a heart rate reading. 2. If a valid heart rate reading is detected, another beep tone will be heard and the screen below will be displayed. Remove your fingers. 3. To exit Heart Rate Mode, remove your fingers for 3 seconds or press MODE. TIP For accurate heart rate reading, make sure: • you are not running or doing exercise • to wear the watch on your wrist and your fingertips touch the 2 metallic plates If you cannot get your heart rate reading within 10 seconds or if any unusual condition occur during heart rate reading: • moisten your fingertips • make sure your fingertips are warm and steady • do not press too hard on the metallic plates • make sure the metallic plates and the back of your watch are clean NOTE • Heart rate measurement cannot be activated if keypad is locked or battery power is low. • Clean the watch with a soft dry cloth. • The 2 metallic plates are very sensitive. Accidentally touching them will trigger heart rate measurement. Hence, to prevent from accidentally activating heart rate measurement, you can select to lock the keypad. • If the battery power is low, the screen below will be displayed. OPERATING MODES The watch has 3 operating modes. Press MODE to toggle between these modes. TIME MODE • This mode displays the real-time clock and date. • To set the time and date, refer to "Time Setting Mode" in Set Up Mode. STOPWATCH MODE (CHRONO) You can take your calorie reading in this mode. To start or stop stopwatch: Press ST/SP/+. To take calorie reading: Take a heart rate reading while the stopwatch is running in order to view the calories burned. Refer to "Heart Rate Measurement". The calorie reading shown in Stopwatch Mode represents an average of the calories lost during the time elapsed. TIP The more frequent you provide heart rate reading, the more accurate the calorie calculation. To reset stopwatch and calorie value: Stop or pause the stopwatch, then press and hold SET/ RST for 2 seconds. NOTE • Set Up Mode cannot be accessed while stopwatch is running. • If stopwatch is running, pressing MODE will go to Time Mode. • Unless you stop the stopwatch, will blink to remind you that the stopwatch is still timing. SET UP MODE There are 4 setting sub-modes in Set Up Mode. • Press - or ST/SP/+ to toggle between these sub-modes. • Press MODE anytime to return to Time Mode. NOTE icon will be displayed in setting sub-mode. TIME SETTING MODE To set time and date: 1. In Time Setting Mode, press SET/RST to enter settings. 2. Press - or ST/SP/+ to set the values. Press and hold - or ST/SP/+ to rapidly change the values. The setting sequence is as follows: 12 / 24-hour time; hour; minute; year; day-month / month-day; month; day. 3. Press SET/RST to confirm and to move to the next setting. 4. Press MODE anytime to confirm and exit settings. ALARM SETTING MODE To set alarm: 1. In Alarm Setting Mode, press SET/RST to enter settings. 2. Press - or ST/SP/+ to turn alarm On or Off. indicates the alarm is turned On. If alarm Off is selected, press MODE to confirm and exit settings. If alarm On is selected, press SET/ RST to confirm and set the alarm time. 3. Press - or ST/SP/+ to set the values. Press and hold - or ST/SP/+ to rapidly change the values. The setting sequence is as follows: hour; minute. 4. Press SET/RST to confirm and to move to the next setting. 5. Press MODE anytime to confirm and exit settings. To silence alarm: • Press any button to stop the alarm and it will activate 24 hours later. OR • Turn the alarm Off in Alarm Setting Mode. BEEP TONE SETTING MODE To turn beep tone On or Off: 1. In Beep Tone Setting Mode, press SET/RST to enter settings. 2. Press - or ST/SP/+ to turn beep tone On or Off. indicates the beep tone is turned Off. 3. Press Mode anytime to confirm and exit settings. USER DATA SETTING MODE To enjoy the full benefits of this watch, set up your personal data before you exercise. This will enable the watch to calculate the level of calories burned while exercising. This information helps you track your progress over time. To set personal data: 1. In User Data Setting Mode, press SET/RST to enter settings. 2. Press - or ST/SP/+ to set the values. Press and hold - or ST/SP/+ to rapidly change the values. The setting sequence is as follows: year of birth; month of birth; day of birth; weight unit; weight. 3. Press SET/RST to confirm and to move to the next setting. 4. Press MODE anytime to confirm and exit settings. BACKLIGHT AND KEYPAD LOCK To activate backlight: Press / to turn backlight On for 5 seconds. NOTE The backlight function will not operate if " " or " " is displayed. To toggle keypad lock On or Off: Press and hold / keypad is locked. for 2 seconds. indicates PHYSICAL CONDITION AND WORKOUT To help achieve maximum health benefits from your workout program, it is important to know your: • Maximum heart rate (MHR) • Upper heart rate limit • Lower heart rate limit MHR is expressed in beats per minute. You can get your MHR from an MHR test, or you can estimate it by using the following formula: 220 - age = MHR TRAINING ZONES There are several training zones that are relevant to a fitness program. The most popular zone range is from 50% to 80% of your maximum heart rate. This is where you achieve cardiovascular benefits, burn fat, and become fitter. When programming your watch, the lower percentage of the zone you choose becomes your lower heart rate limit and the higher percentage becomes the upper heart rate limit. 50% 60% 70% 80% 90% 100% Moderate Activity Weight Management Aerobic Zone Anaerobic Threshold Zone Red Line Zone ( maximum capacity ) There are three training zones, as described below: TRAINING ZONE Health Maintenance Aerobic Exercise Anaerobic Exercise MHR% 65-78% 65-85% 78-90% DESCRIPTION This is the lowest training intensity level. It is good for beginners and those who want to strengthen their cardiovascular systems. Increases strength and endurance. It works within the body's oxygen intake capability, burns more calories and can be maintained for a long period of time. Generates speed and power. It works at or above the body's oxygen intake capability, builds muscle, and cannot be maintained for a long period of time. The upper and lower heart rate limits are calculated by multiplying your MHR by the percentages of the selected training zone. For example: A 40-year-old training for basic health maintenance: • His Upper Heart Rate Limit [220 - 40(age)] x 78% • His Lower Heart Rate Limit [220 - 40(age)] x 65% IMPORTANT Always warm up before exercise and select the training zone that best suits your physique. Exercise regularly, 20 to 30 minutes per session, three to four times a week for a healthier cardiovascular system. WARNING Determining your individual training zone is a critical step in the process towards an efficient and safe training program. Please consult your doctor or health professional to help you determine exercise frequency and duration appropriate for your age, condition and specific goals. USE IN THE WATER The SE138 watch is water-resistant up to 50 meters (164 feet). 50M / 164 FEET RAIN SPLASHES ETC SHOWERING LIGHT (WARM/ SWIMMING/ COOL SHALLOW WATER WATER ONLY) SHALLOW DIVING/ SURFING/ WATER SPORTS OK OK OK OK SNORKELING/ DEEP WATER DIVING NO NOTE Set the watch before exposing it to excessive water. Pressing the keys while in the water or during heavy rainstorms may cause water to enter the watch. SPECIFICATIONS Real time clock Stopwatch Heart rate Calorie range Power Operating temperature Storage temperature 12/24 hour format with hour / minute 00:00:00 to 99:59:59 (hrs: min: sec) 40 - 240 bpm 0 - 9999 kcal 1 x CR2032 3V battery 0°C to 40°C (32°F to 104°F) -20°C to 60°C (-4°F to 140°F) PRECAUTIONS To ensure you use your product correctly and safely, read these warnings and the entire user manual before using the product: • Use a soft, slightly moistened cloth. Do not use abrasive or corrosive cleaning agents, as these may cause damage. Use lukewarm water and mild soap to clean the watch thoroughly after each training session. Never use the product in hot water or store it when wet. • Do not subject the product to excessive force, shock, dust, temperature changes, or humidity. Never expose the product to direct sunlight for extended periods. Such treatment may result in malfunction. • Do not tamper with the internal components. Doing so will terminate the product warranty and may cause damage. The main unit contains no user-serviceable parts. • Do not scratch hard objects against the LCD display as this may cause damage. • Take precautions when handling all battery types. • Remove the batteries whenever you are planning to store the product for a long period of time. • When replacing batteries, use new batteries as specified in this user manual. • The product is a precision instrument. Never attempt to take this device apart. Contact the retailer or our customer service department if the product requires servicing. • Do not touch the exposed electronic circuitry, as there is a danger of electric shock. • Check all major functions if the device has not been used for a long time. Maintain regular internal testing and cleaning of your device. Have your watch serviced by an approved service center annually. • When disposing of this product, ensure it is collected separately for special treatment and not as normal household waste. • Due to printing limitations, the displays shown in this manual may differ from the actual display. • The contents of this manual may not be reproduced without the permission of the manufacturer. NOTE The technical specifications for this product and the contents of the user manual are subject to change without notice. ABOUT OREGON SCIENTIFIC Visit our website (www.oregonscientific.com) to learn more about Oregon Scientific products. If you're in the US and would like to contact our Customer Care department directly, please visit: www2.oregonscientific.com/service/support.asp OR Call 1-800-853-8883. For international inquiries, please visit: www2.oregonscientific.com/about/international.asp. EU-DECLARATION OF CONFORMITY Hereby, Oregon Scientific, declares that this Strapless Heart Rate Monitor (model SE138) is in compliance with EMC directive 89/336/CE. A copy of the signed and dated Declaration of Conformity is available on request via our Oregon Scientific Customer Service. CARDIO-FREQUENCEMETRE SANS CEINTURE MODELE : SE138 MANUEL DE L'UTILISATEUR FR SOMMAIRE Nous vous remercions d'avoir choisi le cardio-fréquencemètre sans ceinture Oregon ScientificTM (SE138). Le modèle SE138 est un aide précieuse pour toutes vos activités physiques et de fitness puisqu'il contrôle vos pulsations cardiaques sans recourir à un émetteur de pulsations cardiaques. Il est équipé d'un outil de mesure des calories, d'une horloge, d'un chronomètre, des fonctions rétro-éclairage et verrouillage des touches. BOUTONS DE COMMANDE 6 3 1 4 2 5 7 1. -: Permet d'alterner entre les sous modes de réglages et de diminuer les valeurs 2. MODE : Permet d'alterner entre les modes, de confirmer un réglage et de sortir 3. ST/SP/ + : Permet de lancer/arrêter le chronomètre, d'alterner entre les sous modes de réglages et d'augmenter les valeurs 4. / : Active le rétro-éclairage et le verrouillage des touches 5. SET/RST: Permet d'entrer dans les sous mode de réglage, de confirmer un réglage, de réinitialiser le chronomètre et les valeurs de calories 6. Plaque métallique supérieure : Appuyez pour entrer dans le Mode de pulsations cardiaques et pour mesurer vos pulsations 7. Plaque métallique inférieure : Appuyez pour entrer dans le Mode de pulsations cardiaques et pour mesurer vos pulsations ECRAN LCD 1 11 2 12 3 4 13 14 5 15 16 6 17 7 8 18 9 10 1. : Indique que vous êtes en Mode Chronomètre ou que le chronomètre est en fonctionnement 2. : Indique que l'alarme est activée 3. : Indicateur vous permettant de diminuer les valeurs 4. : Indicateur vous permettant d'alterner entre les sous modes de réglages 5. Affiche le chronomètre, la date et les bannières des modes 6. : Indique qu'un relevé de pulsation cardiaque est détecté 7. : Horloge format 12 H 8. : Indicateur vous permettant de sortir rapidement et de revenir au mode précédent 9. : Unité de mesure de calories 10. : Unité de poids 11. : Indique que vous êtes dans les sous modes d'un réglage 12. : Indique le bip est désactivé 13. : Indicateur vous permettant d'augmenter les valeurs 14. : Indicateur vous permettant d'alterner entre les sous modes de réglages 15. : Indique que les touches sont verrouillées 16. ou : Indique que la pile est faible 17. Affiche l'heure ou les relevés de calories 18. : Indicateur vous permettant de confirmer le réglage et de passer au suivant AU COMMENCEMENT METTRE EN MARCHE LA MONTRE (UNIQUEMENT LORS DE LA PREMIÈRE UTILISATION) Appuyez et maintenez n'importe quelle touche appuyée jusqu'à ce que l'écran s'active. REGLER L'HEURE ET LES DONNEES DE L'UTILISATEUR Pour utiliser correctement la montre afin de calculer les calories consommées (sur la base de l'âge de l'utilisateur, de son poids, des relevés de pulsations et du temps d'exercice), il est recommandé de régler l'heure et les données personnelles dans le Mode Réglage. Reportezvous à « Mode de Réglage de l'heure » et « Mode de Réglage des données utilisateurs » dans le Mode Réglage. IMPORTANT Rappelez-vous de régler l'heure et les données utilisateurs après avoir remplacé la pile ou après avoir réinitialisé l'appareil. REMPLACER LA PILE La montre fonctionne avec une pile 3V CR2032, d'ores et déjà installée. Si ou clignote, la pile est faible et doit être remplacée. Si la pile est faible, le bip de l'alarme, le rétro-éclairage et les fonctions de mesure des pulsations cardiaques seront désactivés. 1. Utilisez un petit tournevis pour retirer le couvercle du compartiment des piles. Une fois ouvert, placez les vis dans un endroit où vous êtes certain de les récupérer. 2. Remplacez la pile usagée et insérez la nouvelle en respectant les signes de polarité. 3. Replacez le couvercle en le revissant. MESURE DES PULSATIONS CARDIAQUES Vous pouvez mesurer à tous moments vos pulsations cardiaques (sauf dans les sous modes de réglages). 1. Mettez la montre au poignet et placez votre doigt (index ou majeur) sur les deux plaques métalliques pour entrer dans le Mode de Pulsations cardiaques. Un bip sonne et "HR" s'affiche à l'écran lors de toute détection de pulsations cardiaques. La détection des pulsations cardiaques prend entre 6 et 10 secondes. 2. Si une pulsation cardiaque valide est détectée, un autre bip sonne et l'écran suivant s'affiche. 3. Pour sortir du Mode de Pulsations Cardiaques, retirez vos doigts ou appuyez sur MODE pendant 3 secondes. ASTUCE Pour obtenir un relevé précis des pulsations cardiaques, assurez-vous: • que rester immobile et ne pas faire d'exercice. • de porter la montre au poignet et de poser les doigts sur les deux plaques métalliques. Si vous n'obtenez aucun relevé de pulsations cardiaques en l'espace de 10 secondes, ou si vous constatez des conditions inhabituelles pendant la lecture des pulsations : • humectez-vous les doigts • faites en sorte que vos doigts soient chauds et stables sur la plaque métallique • n'appuyez pas trop fort sur les plaques métalliques • assurez-vous que les plaques métalliques et l'arrière de la montre soient propres REMARQUE • Les mesures de pulsations cardiaques ne peuvent être activées si les touches sont verrouillées ou si la pile est faible. • Nettoyez la montre avec un tissu doux et sec. • Les 2 plaques métalliques sont très sensibles. Toucher accidentellement les plaques enclenchera la mesure des pulsations. Ainsi, pour empêcher l'activation accidentelle des mesures de pulsations, verrouillez les touches. • Si la pile est faible, l'écran ci-dessous s'affichera. MODES DE FONCTIONNEMENT La montre est équipée de 3 modes de fonctionnement. Appuyez sur MODE pour alterner entre les modes. MODE HEURE • Ce mode affiche la date et l'heure en temps réel. • Pour régler l'heure et la date, reportez-vous au « Mode de Réglage de l'heure » dans Mode Réglage. MODE CHRONOMETRE (CHRONO) Vous pouvez visualiser les relevés de consommation de calories dans ce mode. Pour lancer ou arrêter le chronomètre : Appuyez sur ST / SP / +. Pour visualiser les relevés de la consommation de calories : Mesurez vos pulsations cardiaques, le chronomètre en fonctionnement dans le but de visualiser les calories consommées. Reportez-vous à « Mesures des pulsations cardiaques ». Les relevés des calories consommées dans le Mode Chronomètre représentent une moyenne des calories perdues pendant la période de temps écoulée. ASTUCE Plus vous mesurez vos pulsations cardiaques, plus les relevés de la consommations de calories seront exacts. Réinitialiser le chronomètre et les valeurs de calories: Arrêtez ou mettez le chronomètre en pause, puis appuyez et maintenez SET/RST pendant 2 secondes. REMARQUE • Vous ne pouvez pas accéder au mode réglage si le chronomètre est en fonctionnement. • Si le chronomètre est en fonctionnement, appuyez sur MODE et vous accéderez au Mode Heure. • A moins que vous n'arrêtiez le chronomètre, l'icône clignotera dans tous les modes, pour vous rappeler que le chronomètre est encore en marche. MODE RÉGLAGE Il y a 4 sous modes réglages dans le Mode Réglage. • Appuyez sur - ou ST/SP/+ pour alterner entre les sous modes. • Appuyez sur MODE pour revenir au mode Heure. REMARQUE L'icône Réglage. s'affichera dans le sous mode MODE DE REGLAGE DE L'HEURE Pour régler l'heure et la date : 1. En mode de réglage de l'heure, appuyez sur SET/RST pour entrer dans les réglages. 2. Appuyez sur - ou ST/SP/+ pour régler les valeurs. Appuyez et maintenez - ou ST/SP/+ pour modifier rapidement les valeurs. Les réglages se présentent dans l'ordre suivant : Heure : format 12 ou 24 h ; heure ; minute ; année ; jour-mois / mois-jour ; mois ; jour. 3. Appuyez sur SET/RST pour confirmer le réglage et passer au suivant. 4. Appuyez sur MODE pour confirmer et sortir. MODE DE REGLAGE DE L'ALARME Pour régler l'alarme : 1. En mode de réglage de l'alarme, appuyez sur SET/RST pour entrer dans les réglages. 2. Appuyez sur - ou ST/SP/+ pour activer ou désactiver l'alarme. indique que l'alarme est activée. Si l'alarme est désactivée, appuyez sur MODE pour confirmer et sortir des réglages. Si l'alarme est activée, appuyez sur SET/RST pour confirmer et régler l'heure de l'alarme. SE138_OSI-USA_MU_R0.indd 1 1/9/08 12:00:20 PM