Oregon Scientific WMR80A User Manual - Page 4

Outdoor Temperature / Humidity, Sensor, Getting Started, Set Up Remote Wind Sensor, Set Up Remote - temperature and humidity sensor for

Get Oregon Scientific WMR80A PDF manuals and user guides View all Oregon Scientific WMR80A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

EN 1. Funnel 2. Indicator OUTDOOR TEMPERATURE / HUMIDITY SENSOR 5 2 1 3 CF 4 1. Unscrew the anemometer from the wind sensor carefully. 2. Insert batteries matching the polarities (+ / -) and replace the anemometer. Press RESET after each battery change. ３a ３b 3. Secure the sensor connector in the desired location: a. Align the back of the sensor connector to an existing pole. Secure in place by inserting the ends of the U-bolt into the holes on the sensor connector and securing it with washers and bolts. OR b. Insert 4 type A screws into the holes of the sensor connector. Screw firmly into place, i.e., fence. 1. LED status indicator 2. RESET hole 3. °C / °F: Select temperature unit 4. CHANNEL switch 5. Battery compartment GETTING STARTED SET UP REMOTE WIND SENSOR The wind sensor takes wind speed and direction readings. The sensor is battery operated. It is capable of transmitting data to the base station wirelessly within an approximate operating range of 100 meters (328 feet). IMPORTANT Ensure that the wind sensor is pointing North to enable it to record accurate readings. NOTE The sensor should be positioned in an open area away from trees or other obstructions. To insert batteries: 2 1 4. Slide wind vane onto the smaller end of the sensor connector. NOTE Use alkaline batteries for longer usage and consumer grade lithium batteries in temperatures below freezing. SET UP REMOTE TEMPERATURE / HUMIDITY SENSOR The remote sensor can collect data from up to 3 channels. To set up the remote sensor: 1. Slide open the battery door. 2. Slide channel switch to select a channel (1, 2, 3). Ensure you use a different channel for each sensor. 3. Insert the batteries, matching the polarities (+ / -). 4. Press RESET after each battery change. 5. Close the battery door. NOTE Install batteries in the remote sensor before the base station matching the polarities (+ and -). 6. Initiate a sensor search on the base station to start receiving temperature / humidity data from the sensor. 4 WMR80_IM_EN_R1.indd 4 2008.7.1 7:11:10 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
4
EN
1. Funnel
2. Indicator
OUTDOOR TEMPERATURE / HUMIDITY
SENSOR
1. LED status indicator
2.
RESET
hole
3.
°C / °F:
Select temperature unit
4.
CHANNEL
switch
5. Battery compartment
GETTING STARTED
SET UP REMOTE WIND SENSOR
The wind sensor takes wind speed and direction
readings.
The sensor is battery operated.
It is capable of
transmitting data to the base station wirelessly within an
approximate operating range of 100 meters (328 feet).
IMPORTANT
Ensure that the wind sensor is pointing
North to enable it to record accurate readings.
NOTE
The sensor should be positioned in an open area
away from trees or other obstructions.
To insert batteries:
1
2
1. Unscrew the anemometer from the wind sensor
carefully.
2. Insert batteries matching the polarities (+ / -) and
replace the anemometer.
Press
RESET
after each
battery change.
3.
Secure the sensor connector in the desired location:
a.
Align the back of the sensor connector to an
existing pole.
Secure in place by inserting the ends
of the U-bolt into the holes on the sensor connector
and securing it with washers and bolts.
OR
b.
Insert 4 type A screws into the holes of the sensor
connector. Screw firmly into place, i.e., fence.
4.
Slide wind vane onto the smaller end of the sensor
connector.
NOTE
Use alkaline batteries for longer usage and
consumer grade lithium batteries in temperatures below
freezing.
SET UP REMOTE TEMPERATURE / HUMIDITY
SENSOR
The remote sensor can collect data from up to 3 channels.
To set up the remote sensor:
1.
Slide open the battery door.
2.
Slide channel switch to select a channel (1, 2, 3).
Ensure you use a different channel for each sensor.
3.
Insert the batteries, matching the polarities (+ / -).
4.
Press
RESET
after each battery change.
5.
Close the battery door.
NOTE
Install batteries in the remote sensor before the
base station matching the polarities (+ and -).
6.
Initiate a sensor search on the base station to start
receiving temperature / humidity data from the sensor.
1
5
2
3
4
C
F
３
a
３
b
WMR80_IM_EN_R1.indd
4
2008.7.1
7:11:10 PM