Panamax MOD-AT4 Manual - Page 1
Panamax MOD-AT4 Manual
UPC - 050616007702
View all Panamax MOD-AT4 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
INSTRUCTIONS FOR PANAMAX SIGNAL LINE PROTECTION MODULES - PREMIUM SERIES Pull Out Pull Out LINE EQUIP IN OUT MOD-AT2 MOD-AT2 LINE IN S110D LINE IN RJ-45 LINE IN RJ-14 LINE IN RJ-11 LINE IN RJ-11 MOD-AT4 EQUIP OUT RJ-45 EQUIP OUT RJ-14 EQUIP OUT RJ-11 EQUIP OUT RJ-11 EQUIP OUT S110D MOD-AT4 Pull Out Pull Out LINE IN S110D MOD-AT8110 EQUIP OUT S110D LINE IN S110D LINE IN RJ-45 LINE IN RJ-14 LINE IN RJ-11 LINE IN RJ-11 MOD-DT4 EQUIP OUT RJ-45 EQUIP OUT RJ-14 EQUIP OUT RJ-11 EQUIP OUT RJ-11 EQUIP OUT S110D MOD-AT8110 MOD-DT4 Pull Out Pull Out MOD-UTP LINE EQUIP. IN OUT MOD-UTP MOD-CAT5 MOD-CAT5 Pull Out Pull Out Card MOD-DBSTV SAT / CATV LINE IN RJ-11 EQUIP OUT RJ-11 SAT / CATV SAT / CATV MOD-DBSTV 1 1 OUTSIDE LINES MOD-SPKP RECEIVER 2 2 3 3 4 4 5 5 6 6 7 7 8 8 MOD-SPKP These modules are approved accessories for use with compatible Panamax AC base units. Compatible base units include the following: Pull Out Model: MOD-AT2 (Secondary Protector) 1-8 MOD-AT2 LINE EQUIP IN OUT WIRING DIAGRAM AND SPECIFICATIONS MOD-AT2 For Analog Telephone Lines 1 - 8 • 4 Wires (1 RJ-14) Protected • 260 Volt Clamping • Auto-resetting PTC's The MOD-AT2 module is designed to protect standard phone lines connected to computer modems, telephones, pay-per-view ports, etc. It will also protect DSL lines (ADSL, G.Lite) going into the DSL modem. The MOD-AT2 module will protect a single phone line using an RJ-11 (2 wire) cord or a dual phone line using an RJ-14 (4 wire) cord. 1. Connect the telephone line to the LINE jack on the module. 2. Use a modular cord to connect the EQUIP modular jack to the equipment to be protected. CURRENT PRODUCTS AC Base Units DISCONTINUED PRODUCTS AC Base Units M8HT-PRO M8-HT PM8-HT PM8-EX M4-EX M8C-EX PM8T-EX M4T-EX M8DBS-EX PM8C-EX M8-EX M8C-Pro PM8DBS-EX M8C-EX M8HC-Pro M4 M8 M4T M8T M4L M8C M8KSU M8COM M8KSU When properly installed, the base unit's Connected Equipment Protection Policy remains valid. All modules include a small rectangular bracket and mounting screws. This bracket replaces the small triangular wall-mount bracket that comes with the models listed in the CURRENT PRODUCTS above. Model: MOD-AT4 (Secondary Protector) Pull Out LINE IN S110D LINE IN RJ-45 LINE IN RJ-14 LINE IN RJ-11 LINE IN RJ-11 MOD-AT4 EQUIP OUT RJ-45 EQUIP OUT RJ-14 EQUIP OUT RJ-11 EQUIP OUT RJ-11 EQUIP OUT S110D 1 - 8 WIRING DIAGRAM AND SPECIFICATIONS Bl Bl Or Or Gr Gr Br Br 1-8 1-4 1 - 4 1-4 1-4 1-4 1-4 MOD-AT4 For Analog Telephone Lines • 4 Pairs (8 wires) Protected • 260 Volt Clamping • Straight-Through Pinout Installation Instructions 1. Mount the rectangular bracket to the back of the AC base unit with the #8-32 x 5/16" machine screws. Note: The brass ground connector must be used with the bracket in order to bond the module ground to the base unit's ground. 2. Mount the signal line module to the bracket (screws provided with the module). 3. Optional - The assembled base unit and module(s) may be wall mounted if desired. Ground Connector Ground Connector Module Bracket Pull Out Card The MOD-AT4 module is designed to protect standard phone lines and DSL (ADSL, G.Lite) lines. Multiple input & output jacks provide complete installation flexibility. The following diagram shows how the jacks/wires are interconnected. Different cables/connections can be split or combined to accommodate a variety of installations. For example: • Two RJ14 (dual-line) cords connected to the LINE side (upper 2 jacks) can be split to four RJ11 (single-line) cords on the EQUIP side. • Four RJ11 (single-line) cords connected to the LINE side can be combined into a single RJ45 (8 wire) cord (upper jack) on the EQUIP side. • Incoming lines can be punched-down on the 110 jack on the LINE side and four RJ11 (single-line) cords will connect from the EQUIP side to the equipment. Caution: Never install telephones during a lightning storm. 4. Connect the wiring to the signal line module as shown in the appropriate following section. Ground Connector Model: MOD-AT8110 (Secondary Protector) All telephone input/output connections will be labeled with LINE and EQUIP. LINE EQUIP. IN OUT It is very important to connect telephone signal lines properly. There are no designated input/output connections on coaxial protection modules. These are bi-directional modules in both transmission frequency and voltage. SAT / CATV AC Base Unit An easy access PULL OUT card is included on the back of each module for wiring diagrams and specifications. 800-472-5555 www.panamax.com Pull Out Pull Out LINE IN S110D L I EQUIP OUT S110D The MOD-AT8110 module is designed to protect up to 8 standard phone lines using 110 punchdown connectors on both the input LINE and output EQUIP. 1. Cut the cable from the primary protector to the correct length and punch down the 1 MOD-AT8110 WIRING DIAGRAM AND SPECIFICATIONS Blue Blue Orange Orange Green Green Brown Brown Blue Blue Orange Orange Green Green Brown Brown 110 MOD-AT8110 110 IDC For Analog Telephone Lines IDC • 16 Wires (two 110 punch-downs) Protected • 260 Volt Clamping • Auto-resetting PTC's cable to the LINE IN punchdown block on the module. 2. Punch down another cable to the EQUIP OUT punchdown block on the module and connect to the phone equipment.