Panasonic 42PWD8UK Plasma Display - Page 9

Connections - th power supply

Get Panasonic 42PWD8UK - 42inch Plasma Panel PDF manuals and user guides
UPC - 037988240890
View all Panasonic 42PWD8UK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Connections When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker's Installation Manual for details on speaker installation. (Example: TH-42PWD8UK) Speakers (Optional accessories) 1 2 1 SPEAKERS SPEAKERS Terminals (R) Terminals (L) AC cord connection (see page 13) 2 - AC cord fixing 1. Open the clamper. 2. I n s e r t t h e A C c o r d and close the clamper securely. 3. Slide up the clamper and fix the AC cord plug securely. When loosen the clamper: 4. Insert the point of the fixed clamper into the small hole on the lower right of the back cover as necessary. Clamper AC cord Note: The power plug in the illustration may not be the type fitted to your set. - Cable fixing bands Secure any excess cables with bands as required. Pass the attached cable fixing band through the clip as shown in the figure. To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure. While ensuring there is sufficient slack in cables to minimize stress (especially in the power cord), firmly bind all cables with the supplied fixing band. To tighten: Pull To loosen: Push the catch 1 2 Pull SLOT1 R AUDIO L IN VIDEO IN VIDEO OUT S VIDEO IN AV SLOT2 R AUDIO L PR/CR/R PB/CB/B Y/G COMPONENT/RGB IN SLOT3 AUDIO PC IN SERIAL Optional Terminal Board Insert Slot (covered) AV Terminals (see page 12) COMPONENT/RGB IN and Audio IN Terminals (see page 12) From EXTERNAL monitor terminal on Computer (see page 10) Notes: • At factory shipment, Terminal boards are installed in SLOT 2 and SLOT 3. • TH-37PWD8UK / TH-37PHD8UK have two slots only. From SERIAL Terminal on Computer (see page 11) 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
9
Connections
1
2
SERIAL
PC
IN
AUDIO
SLOT1
SLOT2
SLOT3
VIDEO IN
VIDEO OUT
P
R
/C
R
/R P
B
/C
B
/B
Y/G
AUDIO
R
L
COMPONENT/RGB IN
AUDIO
IN
R
L
AV
S VIDEO IN
1
2
1
2
SPEAKERS
Terminals (R)
SPEAKERS
Terminals (L)
– Cable
fi
xing bands
Secure any excess cables with bands as required.
When connecting the speakers, be sure to use only the optional accessory speakers.
Refer to the speaker’s Installation Manual for details on speaker installation.
(Example: TH-42PWD8UK)
Speakers (Optional accessories)
Pass the attached cable
fi
xing band through the
clip as shown in the
fi
gure.
To secure cables connected to Terminals, wrap the cable
fi
xing band around them then
pass the pointed end through the locking block, as shown in the
fi
gure.
While ensuring there is suf
fi
cient slack in cables to minimize stress (especially
in the power cord),
fi
rmly bind all cables with the supplied
fi
xing band.
From SERIAL
Terminal on Computer
(see page 11)
From EXTERNAL
monitor terminal on
Computer (see page 10)
AC cord connection (see page 13)
AV Terminals
(see page 12)
To tighten:
To loosen:
Pull
Pull
Push the catch
3.
Slide up the clamper and
fi
x
the AC cord plug securely.
2.
Insert the AC cord
and close the clamper
securely.
1.
Open the clamper.
Clamper
AC cord
Note:
The power plug in the illustration may not be the type
fi
tted to your set.
When loosen
the clamper:
Notes:
• At factory shipment, Terminal boards are installed in SLOT 2 and SLOT 3.
• TH-37PWD8UK / TH-37PHD8UK have two slots only.
– AC cord
fi
xing
4.
Insert the point of the
fi
xed clamper into the
small hole on the lower
right of
the back
cover as
necessary.
Optional Terminal
Board Insert Slot
(covered)
COMPONENT/RGB IN
and Audio IN Terminals
(see page 12)