Panasonic AG-HVX200PJ Operating Instructions - Page 72

Number Of Clips, Serial No.

Get Panasonic AG-HVX200PJ PDF manuals and user guides View all Panasonic AG-HVX200PJ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Thumbnail operations (continued) P2 card information screen 1 2 3 4 5 1 Write protection mark 2 P2 card status The amount of memory remaining on the P2 card is displayed using a percentage bar. The following displays may appear, depending on the card status. FORMAT ERROR: An unformatted P2 card has been inserted. NOT SUPPORTED: A card not supported by the unit has been inserted. NO CARD: A card has not been inserted. • The information on the card in the selected slot (indicated by the yellow number) can be viewed by pressing the SET button. BRAND: Name of manufacturer MODEL NO.: Model number SERIAL NO.: Serial number USER ID: User ID WARNING: Warning information 3 P2 card remaining memory/total memory The P2 card's remaining memory and total memory are displayed here in 1-minute increments. Fractions of a minute are rounded off, meaning the display may not match the slot total. 4 Card warning mark This mark is displayed when one of the following warnings applies to a P2 card. 1) RUN DOWN CARD (page 94) 2) DIR ENTRY NG CARD (page 94) • The contents of the warning can be viewed by checking the card information as described above. P2 5 Slot total The figure represents the total remaining memory of the cards in the two slots. If a P2 card is write-protected, its remaining memory will not be included in the total remaining memory. • When LOOP is set under REC FUNCTION, the slot total represents the guaranteed minimum recording time for loop recording. However, note that when PROPERTY SETUP: USED is selected in step 3 on the previous page, the used amount displayed by the slot total will be larger than the actual amount, and when PROPERTY SETUP: REMAIN is selected, the remaining amount displayed by the slot total will be smaller than the actual amount. (Page 50) SD memory card information screen THUMBNAIL OPERATISODNSTANDARD : PROPERUTSYED META DABTALANK EXIT TOTAL NUMBER OF CLIPS PROTECT OK : SUPPORTED : 96 KB : 122.3 MB ! : 122.4 MB : : OFF SD STANDARD: This indicates whether the SD memory card was formatted in compliance with the SD or SDHC standard. (SUPPORTED/NOT SUPPORTED). USED: Space used BLANK: Space available TOTAL: Total space NUMBER OF CLIPS: Number of clips PROTECT: This indicates that the SD memory card is writeprotected. 72

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
72
Thumbnail operations (continued)
P2 card information screen
1
2
3
4
5
1 Write protection mark
2 P2 card status
The amount of memory remaining on the P2
card is displayed using a percentage bar. The
following displays may appear, depending on
the card status.
FORMAT ERROR:
An unformatted P2 card has been inserted.
NOT SUPPORTED:
A card not supported by the unit has been
inserted.
NO CARD:
A card has not been inserted.
• The information on the card in the selected
slot (indicated by the yellow number) can be
viewed by pressing the SET button.
BRAND:
Name of manufacturer
MODEL NO.:
Model number
SERIAL NO.:
Serial number
USER ID:
User ID
WARNING:
Warning information
3
P2 card remaining memory/total memory
The P2 card’s remaining memory and total
memory are displayed here in 1-minute
increments. Fractions of a minute are rounded
off, meaning the display may not match the slot
total.
4 Card warning mark
This mark is displayed when one of the
following warnings applies to a P2 card.
1) RUN DOWN CARD (page 94)
2) DIR ENTRY NG CARD (page 94)
• The contents of the warning can be viewed by
checking the card information as described
above.
5 Slot total
The figure represents the total remaining
memory of the cards in the two slots. If a P2
card is write-protected, its remaining memory
will not be included in the total remaining
memory.
• When LOOP is set under REC FUNCTION,
the slot total represents the guaranteed
minimum recording time for loop recording.
However, note that when PROPERTY
SETUP: USED is selected in step 3 on the
previous page, the used amount displayed
by the slot total will be larger than the actual
amount, and when PROPERTY SETUP:
REMAIN is selected, the remaining amount
displayed by the slot total will be smaller than
the actual amount. (Page 50)
SD memory card information screen
THUMBNAIL
OPERATION
META DATA
EXIT
PROPERTY
SD STANDARD :
: SUPPORTED
USED
: 96 KB
TOTAL
: 122.4 MB
NUMBER OF CLIPS
:
PROTECT
: OFF
BLANK
: 122.3 MB
OK
SD STANDARD:
This indicates whether the SD memory card was
formatted in compliance with the SD or SDHC
standard. (SUPPORTED/NOT SUPPORTED).
USED:
Space used
BLANK:
Space available
TOTAL:
Total space
NUMBER OF CLIPS:
Number of clips
PROTECT:
This indicates that the SD memory card is write-
protected.
P2