Panasonic AJ-PCD35 Operating Instructions - Page 12

continue, Pay attention to the items below if you are, using Mac Pro 1st Generation. - drive

Get Panasonic AJ-PCD35 PDF manuals and user guides View all Panasonic AJ-PCD35 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Installation (continue) 7 Connect the AC adapter included with the P2 drive to the unit's DC IN 16V socket. Start up the P2 drive. Check that the green light on the unit's power indicator turns on and that the status indicators for all card slots blink about once per second. DC IN 16V DC IN 12V For the AJ-PCD35EJ only: Plug the power switch box supplied with the P2 drive into the DC IN 16V socket on the P2 drive, then plug the supplied AC adapter into the power switch box. The P2 drive will start when you turn ON the switch. Confirm that the power indicator on the P2 drive lights green, and that the status indicators for each slot blink for about one second. DC IN 16V DC IN 12V z In Windows XP or Windows Vista, some card slots of the P2 drive may be assigned drive names that have already been assigned to existing networks. Reassign network drive names if your personal computer does not display all five card slots. z Since the P2 drive does not support hotplugging, do not insert or remove the PCI Express cable with the personal computer power on. z While the P2 drive and the personal computer are connected, do not insert or remove the unit's AC adapter when the personal computer is on. If the personal computer is on with the unit off, before turning the unit on, turn the personal computer off. Pay attention to the items below if you are using Mac Pro (1st Generation). z Insert the PCI Express board supplied into the slot 1 or 4 in MAC Pro (1st Generation) (Slot number is for using the number of lanes in a normal condition). If you insert the board into the slot 2 or 3, change the number of slot lanes to a4 or a8 before insertion by selecting "System" > "Library" > "CoreServices" > "Expansion Slot Utility". z If you use more than a8 lanes of RAID interface card and this device in combination, operation speed may be limited due to the setting of the number of lanes. AC adapter Disconnect the AC mains plug from the AC mains socket when not in use. 8 Start up the personal computer. 9 Verify that the personal computer recognises the P2 drive. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
12
Installation
(continue)
7
Connect the AC adapter included with the
P2 drive to the unit’s DC IN 16V socket.
Start up the P2 drive.
Check that the green light on the unit’s
power indicator turns on and that the
status indicators for all card slots blink
about once per second.
For the AJ-PCD35EJ only:
Plug the power switch box supplied with
the P2 drive into the DC IN 16V socket on
the P2 drive, then plug the supplied AC
adapter into the power switch box. The P2
drive will start when you turn ON the
switch.
Confirm that the power indicator on the P2
drive lights green, and that the status
indicators for each slot blink for about one
second.
<Note>
Disconnect the AC mains plug from the
AC mains socket when not in use.
8
Start up the personal computer.
9
Verify that the personal computer
recognises the P2 drive.
<Notes>
z
In Windows XP or Windows Vista, some card
slots of the P2 drive may be assigned drive
names that have already been assigned to
existing networks. Reassign network drive
names if your personal computer does not
display all five card slots.
z
Since the P2 drive does not support hot-
plugging, do not insert or remove the PCI
Express cable with the personal computer
power on.
z
While the P2 drive and the personal computer
are connected, do not insert or remove the
unit’s AC adapter when the personal computer
is on. If the personal computer is on with the
unit off, before turning the unit on, turn the
personal computer off.
DC IN 16V
DC IN 12V
DC IN 16V
DC IN 12V
AC adapter
Pay attention to the items below if you are
using Mac Pro (1st Generation).
z
Insert the PCI Express board supplied into
the slot 1 or 4 in MAC Pro (1st Generation)
(Slot number is for using the number of lanes
in a normal condition).
If you insert the board into the slot 2 or 3,
change the number of slot lanes to
a
4 or
a
8
before insertion by selecting “System”
>
”Library”
>
“CoreServices”
>
”Expansion
Slot Utility”.
z
If you use more than
a
8 lanes of RAID
interface card and this device in combination,
operation speed may be limited due to the
setting of the number of lanes.