Panasonic CQC300U Auto Radio/cd/mp3 Deck - Page 10

Preparation (Clock Adjustment etc

Get Panasonic CQC300U - 50Wx4 iPod-Ready Multi-Format Car Audio Receiver PDF manuals and user guides
UPC - 037988758401
View all Panasonic CQC300U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Preparation Cancellation of Demonstration The demonstration message appears for initial use. 1 Set your car's ignition switch to the ACC or ON position. 5 Turn [VOL] counterclockwise. For using the remote control, press [0] (). 2 Press [PWR] (Power). 3 Hold down [VOL] (PUSH SEL: Select) for 2 sec. or more to open the menu. 4 Press [VOL] (PUSH SEL: Select) to select the Demonstration setting. ("DEMO" is displayed) Notes: • To return to the regular mode, press [DISP]. • Refer to the section on "Function Setting" ( page 23). • When "NO DISC" is displayed, the Demonstration cannot be cancelled. Preparation Before Initial Use Pull the insulation film out from the backside of remote control gently. Warning Keep batteries and insulation film out of reach of infants. If an infant ingests a battery, please seek immediate medical attention. Insulation film Battery Replacement Remove the battery holder with the remote control unit placed on a flat surface.  Stick your thumbnail into the groove, and push the holder in the direction of the arrow, and at the same time.  Pull it out in the direction of the arrow using a tough pointed object. Tough pointed object   Back side   Put a battery in the case with () side facing up.  Put the case back.  Cautions • Remove and dispose of an old battery immediately. • Do not disassemble, heat or short a battery. Do not throw a battery into a fire or water. • Follow local regulations when disposing of a battery. • Improper use of a battery may cause overheating, an explosion or ignition, resulting in injury or a fire. Notice This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. Note: Battery Information: Battery Type: Panasonic lithium battery (CR2025) (Included in the remote control) Battery Life: Approximately 6 months under normal use (at room temperature) Remote Control Preparation Clock Adjustment The 12-hour system is used for the clock. 1 Press [PWR] (Power). 2 Press [DISP]. 3 Hold down [DISP] for 2 sec. or more. 4 Adjust the hour and press [DISP]. []: Forward []: Backward 5 Adjust the minute and press [DISP] to confirm the adjustment. []: Forward []: Backward Notes: • Adjust the clock when "ADJUST" appears on the display. • Hold down [] or [] to change numbers rapidly. • When "NO DISC" is displayed, the clock cannot be adjusted. 10 CQ-C300U

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
CQ-C300U
10
Preparation
The demonstration message appears for initial use.
1
Set your car’s ignition switch to the
ACC or ON position.
2
Press
[PWR]
(Power).
3
Hold down
[VOL]
(
PUSH SEL:
Select)
for 2 sec. or more to open the menu.
4
Press
[VOL]
(
PUSH SEL:
Select) to
select the Demonstration setting.
(“DEMO” is displayed)
5
Turn
[VOL]
counterclockwise.
For using the remote control, press
[0]
(
).
Notes:
• To return to the regular mode, press
[DISP]
.
• Refer to the section on “Function Setting” (
page
23).
• When “NO DISC” is displayed, the Demonstration
cannot be cancelled.
Cancellation of
Demonstration
Remote Control Preparation
Preparation Before Initial Use
Pull the insulation film
out from the backside of
remote control gently.
Battery Replacement
Remove the battery
holder with the remote
control unit placed on a
flat surface.
Stick your thumbnail
into the groove, and
push the holder in
the direction of the
arrow, and at the
same time.
Pull it out in the
direction of the
arrow using a tough
pointed object.
Put a battery in the case
with (
) side facing up.
Put the case back.
Tough pointed object
Back side
The 12-hour system is used for the clock.
1
Press
[PWR]
(Power).
2
Press
[DISP]
.
3
Hold down
[DISP]
for 2 sec. or more.
4
Adjust the hour and press
[DISP]
.
[
]
: Forward
[
]
: Backward
5
Adjust the minute and press
[DISP]
to
confirm the adjustment.
[
]
: Forward
[
]
: Backward
Notes:
•
Adjust the clock when “ADJUST” appears on the display.
• Hold down
[
]
or
[
]
to change numbers
rapidly.
• When “NO DISC” is displayed, the clock cannot be
adjusted.
Cautions
• Remove and dispose of an old battery immediately.
• Do not disassemble, heat or short a battery. Do not
throw a battery into a fire or water.
• Follow local regulations when disposing of a
battery.
• Improper use of a battery may cause overheating,
an explosion or ignition, resulting in injury or a fire.
Warning
Keep batteries and insulation film out of reach of
infants. If an infant ingests a battery, please seek
immediate medical attention.
Note:
Battery Information:
Battery Type: Panasonic lithium battery (CR2025)
(Included in the remote control)
Battery Life: Approximately 6 months under normal use
(at room temperature)
Insulation film
Clock Adjustment
Notice
This product contains a CR Coin Cell Lithium
Battery which contains Perchlorate Material - special
handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.