Panasonic CT27SC14 27" Color Tv - Page 6
Installation - ct 27sl14
View all Panasonic CT27SC14 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 6 highlights
ENGLISH INSTALLATION Installation Television Location Follow these recommendations before deciding the location of your television. • Avoid excessive sunlight or bright lights, including reflections. • Keep away from excessive heat or moisture. Inadequate ventilation may cause internal component failure. • Fluorescent lighting may reduce remote control transmitting range. • Keep away from magnetic equipment, including motors, fans and external speakers. WARNING: Use this television receiver only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. In order to avoid injury to children, never place your television receiver on a piece of furniture that is capable of being tilted by a child leaning on it, pulling on it, standing on it, or climbing on it. A falling television can cause serious injury or even death. CT-27SL14, CT-27SL14U: CAUTION: These television receivers for use only with PANASONIC TY-27SL33T stand. Use with other carts (or stands) is capable of resulting in instability causing possible injury. CT-32SL14, CT-32SL14U: CAUTION: These television receivers for use only with PANASONIC TY-32HL43T stand. Use with other carts (or stands) is capable of resulting in instability causing possible injury. CT-36SL14, CT-36SL14U: CAUTION: These television receivers for use only with PANASONIC TY-36HL43T stand. Use with other carts (or stands) is capable of resulting in instability causing possible injury. Optional Cable Connections Shielded audio and video cables should be used between components. For best results: • Use 75-ohm coaxial shielded cables. • Use appropriate input and output connectors, that match your component connectors. • Avoid long cables to minimize interference. AC Power Supply Cord CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT OF AC OUTLET AND FULLY INSERT. DO NOT Polarized plug USE A PLUG WITH A RECEPTACLE OR OTHER OUTLET UNLESS THE BLADE CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. PROTECT POWER CORDS FROM BEING WALKED ON, ROLLED OVER, CRIMPED, BENT, OR PINCHED, PARTICULARLY AT PLUGS, CONVENIENCE RECEPTACLES, AND THE POINT WHERE THEY EXIT FROM THE APPARATUS. Cable / Antenna Connection For proper reception, either a cable or antenna connection is required. Cable Connection Incoming Cable from Connect the cable supplied by your local Cable Company cable company. Tighten with fingers only. Use of any tool (e.g. pliers) for tightening may result in tuner damage. Note: A cable converter box may be required for proper reception. 75 Ohm VHF/UHF on back of TV Check with your local cable company for compatibility requirements. Antenna Connections • For proper reception of VHF/ Incoming Cable from UHF channels, an external Home Antenna antenna is required. For best reception an outdoor antenna is recommended. Note: Cable Mode is preset at the factory. Antenna users must change to TV Mode in the Set Up menu under Prog Chan (page 13). Remote Control Battery Installation Requires two AA batteries (supplied). Battery Polarity AA / 1.5A 1 2 AA / 1.5A AA / 1.5A AA / 1.5A 3 Procedure 1. Turn the remote control face down. Remove battery cover by pressing down on the marking on the cover and sliding it off in the direction indicated. 2. Install batteries matching (+) and (-) polarity signs. 3. Replace the battery cover by sliding in reverse until the lock snaps. Note: Incorrect installation can cause battery leakage and corrosion that will damage the Remote Control. Precautions • Replace batteries in pair. • Do not mix battery types (zinc carbon with alkaline). • Do not recharge, heat, short-circuit, disassemble, or burn batteries. 4 z