Panasonic DMP-BD70V Blu-ray/vhs Player - Multi Language - Page 40
Troubleshooting guide, To reset this unit, Power, Operation
UPC - 037988983445
View all Panasonic DMP-BD70V manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 40 highlights
Troubleshooting guide Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the chart do not solve the problem, refer to "Customer Services Directory (United States and Puerto Rico)" on page 46 if you reside in the U.S.A.and Puerto Rico, or refer to "Product information" on page 45 if you reside in Canada. The following do not indicate a problem with this unit: ≥Regular disc rotating sounds. ≥Image disturbance during search. To reset this unit To restore the unit if it freezes due to one of the safety devices being activated To return all settings to the factory preset To return to the factory preset (No setting) ≥Press and hold [POWER Í/I] on the main unit for 3 seconds. (The settings remain unchanged.) ≥Select "Yes" in "Restore Default Settings" in the Setup menu. This returns all values in the Setup menu and the on-screen menu, except for "Remote Control Code", "On-screen Language", "IP Address/DNS Settings", "Proxy Server Settings", "DVD-Video Ratings", "BD-Video Ratings" and "Network Service" to the default settings. ≥Reset the unit as follows: 1 Press [POWER Í/I] on the unit to turn off the unit. 2 Press and hold [;], [POWER Í/I] and [< OPEN/CLOSE] on the unit at the same time for more than 5 seconds until "HELLO" is displayed on the unit. 3 The power will turn on and then turn off. Page - 36 - Power Power of this unit is turned ≥If connected with an "HDAVI Control 4" compatible TV (VIERA) with the "Auto - off when the input for the TV power stand-by" setting activated on the TV, when switching the TV input, the unit is changed. will be automatically turned to standby. For details please read the operating instructions of the TV. Operation Cannot operate the television or amplifier/ receiver. The remote control doesn't work properly. ≥Change the manufacturer code of the remote control. In some cases, even if you change the code, the remote control may not be operated depending on the type of the televisions or amplifiers/receivers. ≥It may be necessary to set the manufacturer code or the remote control code again after changing the batteries for remote control. ≥The remote control and main unit are using different codes. Change the code on the remote control. ≥The batteries are depleted. Replace them with new ones. The unit is on but cannot be operated. ≥Confirm the correct drive is selected. ≥One of the unit's safety devices may have been activated. Reset the unit as follows: 1 Press [POWER Í/I] on the main unit to switch the unit to standby. If the unit doesn't switch to standby, press and hold [POWER Í/I] on the main unit for about 3 seconds. The unit is forcibly switched to standby. Alternatively, disconnect the AC power supply cord, wait one minute, then reconnect it. 2 Press [POWER Í/I] on the main unit to switch it on. If the unit still cannot be operated, consult the dealer. ≥Condensation has formed. Wait 1 to 2 hours for it to evaporate. Play fails to start even when [1] (PLAY) is pressed. Play starts but then stops immediately. ≥Insert the media correctly with the label facing up. ≥The media is dirty. ≥You tried to play a blank media or unplayable media on this unit. Cannot eject disc. ≥The unit may have a problem. While the unit is off, press and hold [;] and [< OPEN/CLOSE] on the main unit at the same time for about 5 seconds to force the tray to eject. Remove the disc and consult the dealer. Start up is slow. It takes time before play starts. ≥Make sure that "Quick Start" is set to "On". If connected with an "HDAVI Control 4" compatible TV (VIERA) with the "Stand-by power save" setting activated on the TV, even with "Quick Start" set to "On", when the TV is in standby mode, the unit may take some time to startup. ≥Start up takes time in the following situations. -Immediately after a power failure or the AC power supply cord is connected. -When the unit is connected with an HDMI cable. Played back image is ≥High definition video (transfer rate of 18 Mbps or faster) cannot be played back distorted or does not correctly if it was recorded on a DVD compatible to double speed or slower. playback correctly. ([AVCHD]) Cannot set "On" in "24p Output". 40 ≥Only when the unit is connected to the HDMI terminal of a TV supporting 24p you can select "On". In some cases where the unit is connected to a TV via an amplifier/receiver through the HDMI terminals, you may not be able to select "On". In this case, connect the unit to a TV through the HDMI terminal and connect it to the amplifier/receiver through any terminal other than HDMI. 15 5, 15, 36 36 5 20 - - 19 3 6, 7 - 36 - - 34 RQT9412