Panasonic EW3109ACW Operating Instructions - Page 17

z.-1.

Get Panasonic EW3109ACW PDF manuals and user guides View all Panasonic EW3109ACW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Flash warning system for hypertensive readings If the measured values fall within the hypertension range, the reading displayed on screen flashes on and off to alert user. According to JNC 7 Classification, values consistently in excess of 140 mmHg (Sys.) and/or 90 mmHg (Dia.) are considered to constitute high blood pressure. sp z.-1. SYAXIAm mmHg DIASTOLIC mmHg 4 (01 1 3 ,4I '1pu2,se,m,n Diastolic (mmHg) 90 80 • Blood pressure readings will flash for approx. 6-seconds when in the high blood pressure range. Systolic blood pressure: 140 mmHg and over Diastolic blood pressure: 90 mmHg and over (Only when measurement is complete) Hypertension (Stage 1, Stage 2) Prehypertension Normal 120 140 (mmHg) Systolic When an Error Occurs During Measurement SYSTOLIC mmHg DIASTOLIC mmHg An E will appear on the display to E indicate that measurement was unsuccessful and should be performed pulse/min again. Before performing another measure- ment, always press the On/Off and Start button to turn off the unit and make sure to allow a rest period of 4 to 5 minutes before starting again. Please consult your doctor without delay if the blood pressure indicator repeatedly draws attention to elevated blood pressure values. Advice: In general, blood pressure measurements are lower for the second measurement because you are less nervous and are more tranquil. For people who easily get tense, measuring twice each time is very effective. When two measurements are taken, normally the smaller measurement is stored. When taking two measurements, always stay quiet for 4 to 5 minutes after the first measurement before taking the second measurement. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Flash
warning
system
for
hypertensive
readings
If
the
measured
values
fall
within
the
hypertension
range,
the
reading
displayed
on
screen
flashes
on
and
off
to
alert
user.
According
to
JNC
7
Classification,
values
consistently
in
excess
of
140
mmHg
(Sys.)
and/or
90
mmHg
(Dia.)
are
considered
to
constitute
high
blood
pressure.
SY
A
XI
A
m
mmHg
DIASTOLIC
mmHg
sp
z.-1.
'12
pu,se,m,n
•
Blood
pressure
readings
will
flash
for
approx.
6
-seconds
when
in
the
high
blood
pressure
range.
Systolic
blood
pressure:
140
mmHg
and
Diastolic
blood
pressure:
90
mmHg
and
over
(Only
when
measurement
is
complete)
When
an
Error
Occurs
During
Measurement
An
will
appear
on
the
display
to
indicate
that
measurement
was
unsuccessful
and
should
be
performed
again.
Before
performing
another
measure-
ment,
always
press
the
On/Off
and
Start
button
to
turn
off
the
unit
and
make
sure
to
allow
a
rest
period
of
4
to
5
minutes
before
starting
again.
Please
consult
your
doctor
without
delay
if
the
blood
pressure
indicator
repeatedly
draws
attention
to
elevated
blood
pressure
values.
SYSTOLIC
mmHg
DIASTOLIC
mmHg
E
pulse/min
Advice:
In
general,
blood
pressure
measurements
are
lower
for
the
second
measurement
because
you
are
less
nervous
and
are
more
tranquil.
For
people
who
easily
get
tense,
measuring
twice
each
time
is
very
effective.
When
two
measurements
are
taken,
normally
the
smaller
measurement
is
stored.
When
taking
two
measurements,
always
stay
quiet
for
4
to
5
minutes
after
the
first
measurement
before
taking
the
second
measurement.
16