Panasonic H1 Sd/hdd Video Camcorder - Multi Language - Page 121

Problem, Check points, The unit arbitrarily stops

Get Panasonic H1 - Toughbook - Atom Z540 PDF manuals and user guides
UPC - 092281893006
View all Panasonic H1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 121 highlights

Problem This unit cannot be operated though it is turned on. This unit does not operate normally. The remote control does not function. The remaining time indication or the elapsed time indication is not shown. Recording does not start although power is supplied to this unit and the SD card is correctly inserted. The unit arbitrarily stops recording. Recording starts but stops immediately. Color balance of images is strange when recording in a place such as a gymnasium. Check points ≥ The unit cannot be operated if the LCD monitor is not opened. ≥ Press the RESET button. (l 123) If normal conditions are not restored yet, remove the battery or AC adaptor, wait about 1 minute and then reconnect the battery or AC adaptor. Then about 1 minute later, turn on the power again. (Conducting the above operation while the HDD or SD card is being accessed may damage the data on the HDD or SD card.) ≥ The button-type battery of the remote control may be run out. Replace it with a new button-type battery. (l 20) ≥ If you set [SETUP] > [DISPLAY] > [OFF], all indications other than warnings and date are not displayed. ≥ Rotate the mode dial to select or . ≥ No recording is possible while the SD card's write protect switch is set to LOCK. (l 26) ≥ If there is no more available memory of the SD card or HDD, free up some memory by deleting unnecessary scenes or use a new SD card. (l 27, 74) ≥ If the SD card cover is open, this unit may not operate normally. Close the SD card cover. ≥ Use an SD card that can be used for motion picture recording. (l 26) ≥ If [AGS] is [ON], record in the normal horizontal position or set [AGS] to [OFF]. (l 37) ≥ If the unit is exposed to strong vibrations or shocks while recording on HDD, recording may stop to protect the HDD. ≥ The unit is disabled if the temperature is too high. Turn off the power of the unit and wait until the unit cools down. ≥ In a place with multiple light sources, such as a gymnasium or a hall, the auto white balance function may not operate properly. In this case, adjust the white balance setting manually. (l 63) 121 VQT1N74

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
121
VQT1N74
Problem
Check points
This unit cannot be
operated though it is
turned on.
This unit does not
operate normally.
≥
The unit cannot be operated if the LCD monitor is not
opened.
≥
Press the RESET button. (
l
123) If normal conditions are
not restored yet, remove the battery or AC adaptor, wait
about 1 minute and then reconnect the battery or AC
adaptor. Then about 1 minute later, turn on the power
again. (Conducting the above operation while the HDD or
SD card is being accessed may damage the data on the
HDD or SD card.)
The remote control does
not function.
≥
The button-type battery of the remote control may be run
out. Replace it with a new button-type battery. (
l
20)
The remaining time
indication or the elapsed
time indication is not
shown.
≥
If you set [SETUP]
>
[DISPLAY]
>
[OFF], all indications
other than warnings and date are not displayed.
Recording does not start
although power is
supplied to this unit and
the SD card is correctly
inserted.
≥
Rotate the mode dial to select
or
.
≥
No recording is possible while the SD card’s write protect
switch is set to LOCK. (
l
26)
≥
If there is no more available memory of the SD card or
HDD, free up some memory by deleting unnecessary
scenes or use a new SD card. (
l
27, 74)
≥
If the SD card cover is open, this unit may not operate
normally. Close the SD card cover.
The unit arbitrarily stops
recording.
≥
Use an SD card that can be used for motion picture
recording. (
l
26)
≥
If [AGS] is [ON], record in the normal horizontal position or
set [AGS] to [OFF]. (
l
37)
≥
If the unit is exposed to strong vibrations or shocks while
recording on HDD, recording may stop to protect the HDD.
Recording starts but
stops immediately.
≥
The unit is disabled if the temperature is too high. Turn off
the power of the unit and wait until the unit cools down.
Color balance of images
is strange when
recording in a place such
as a gymnasium.
≥
In a place with multiple light sources, such as a gymnasium
or a hall, the auto white balance function may not operate
properly. In this case, adjust the white balance setting
manually. (
l
63)