Panasonic NCPF30PV NCPF30PV User Guide - Page 5

PartNames, and Handling, lnstructions

Page 5 highlights

PartNamesand Handlinglnstructions Operationpanel lf theprotectivefilmisstillcoveringthesurfaceof theoperationpanel, peelit offbeforeusingtheoperationpanel. Lid openinglever Liquidcrystal display Steamvent Lid Pushplate P u s hp l a t el o c k Handle Pressthe depressionin the lid opening lever,and lift the lid. Lidopenni g lever )lF Depression Push on the lid releaselever,hold the lid opening fever,and pull the lid out and up diagonally. Dispensing spout W i n d o wr i m Gontainer Meshfilter (Replaceable part) It may have beencomeofffromthe bottomof the containerP. ushit completelyintothe correct p o s i t i o n(.S e eP . 1 7 ) M i n i m u mw a t e r level mark Add waterbeforethe lowwaterlevelis reached. Rotatingbase(360degrees) When rotatingthe pot,do notallow thecordto windaroundthe unit. Powercord Cord Bodyplug .Theshapeof plugdiffersaccordingto region. 8 To close Pressdown on the lid untilit clicks. \**-*** To attach Insertthe lid at an angle. lf an empty containeris heated,the overheatsafetyfunction(whichpreventsan empty containerfrom being heated)will be activated.The powerwill be shut off automatically to preventthe problemsthat may occurdue to overheatingT. his will be shown on the displayas shown below. Flashingalternately Causing .Less than the minimumwater levelin the containerwas boiled. .Afterwateris added,the lid mightbe leftopen. Howto cancelthe display Supplwy ateirntothecontainearn, dpress tneffi6"t G@ lf an empty containeris heated,an odor will be emittedand the container may be discolored.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17

PartNames
and Handling
lnstructions
Operation
panel
lf the protective
filmis still
covering
the surface
of the operation
panel,
peel
it off before
using
the operation
panel.
Lid openinglever
Steamvent
Lid
Push
plate
Pushplate
lock
Handle
Gontainer
Minimum
water
level mark
Add waterbefore
the
lowwaterlevel
is
reached.
in the lid
the lid.
Push on the lid release
lever,
hold
the lid opening fever,and pull the
lid out and up diagonally.
To attach
Insert
the lid at an angle.
ng lever
Depression
Liquidcrystal
display
Dispensing
spout
Window
rim
Mesh
filter
(Replaceable part)
It may have beencome off from the bottom
of
the container.
Pushit completely
intothe correct
position.
(SeeP.17)
\**-***
Rotatingbase (360degrees)
When rotating
the pot,
do not allow
the cordto windaround
the unit.
Power
cord
Cord
Body
plug
lf an empty container
is heated,
the overheatsafetyfunction
(whichprevents
an empty
container
from being heated)will be activated.
The power
will be shut off automatically
to prevent
the problemsthat may occur due to overheating.
This will be shown on the
displayas shown below.
Causing
.Less
than the minimum
water levelin the
container
was boiled.
.After
water
is added,the lid might be leftopen.
How to cancel the display
Supply
water
into
the
container,
and
press
tneffi6"t
8
Press the depression
opening lever,and lift
Lidopeni
)lF
To close
Pressdown on the lid untilit clicks.
Flashing
alternately
lf an empty containeris heated,an odor will be emittedand the container
may be discolored.
.The
shape
of plugdiffers
according
to region.
G@