Panasonic PT-LW333 PT-LB423 Series Operating Instructions - Page 70

Power management]

Get Panasonic PT-LW333 PDF manuals and user guides View all Panasonic PT-LW333 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Chapter 4 Settings - [Expand] menu [Off] The projector can be operated without the PIN code. Note ff If you want to correct the digit, press the button to reset the digit and then re-enter it. ff Press the button after moving the cursor to [Cancel] to return the menu screen. ff If you entered an incorrect digit, the digit () will turn red and reset, and then re-enter a digit. [PIN code change] Change the PIN code. 1) Press as to select [Security]. 2) Press the button. ff The [Security] screen is displayed. 3) Press as to select [PIN code change]. 4) Press the button. ff The [PIN code] input screen is displayed. 5) Enter the PIN code you have set according to the steps in "Enter a PIN code". 6) Press the button. ff The [New PIN code] input screen is displayed. 7) Enter the New PIN code according to the steps in "Enter a PIN code". [Power management] This function optimizes lamp power according to the operating status to reduce power consumption. [Power management] Set the operation as following if there is no signal input. 1) Press as to select [Power management]. 2) Press the button. ff The [Power management] screen is displayed. 3) Press as to switch the item. ff The items will switch each time you press the button. [Ready] [Shut down] [Off] [Timer] [Ready Countdown] The countdown timer is displayed after 30 seconds without input signal. The projection lamp turns off and cools down when reaching the set time, meanwhile the projector will enter into the ready mode of the power management. The projection lamp will be turned on if the input signal is reconnected or any button (except for power button ) is pressed. The countdown timer is displayed after 30 seconds without input signal. The projection lamp is turned off and cooled down when reached the set time, then the projector enter into standby status. Power management function is off. Set the time that the Power management starts to work. The time from the state which the management function is working to the standby mode can be set to 0 ~ 30 minutes when [Power management] is set to [Ready]. The increment is 1 minute. Setting [Timer] in step 3) The time that the Power management starts to work can be set to 1-30 minutes. The increment is one minute. 1) Press as to select [Timer]. 2) Press the button. 3) Press as to switch the setting time. ff The setting times will switch each time you press the button. Setting [Ready Countdown] in step 3) The time from the state which the management function is working to the standby mode can be set to 0 ~ 30 minutes when [Power management] is set to [Ready]. The increment is one minute. 70 - ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
70 - ENGLISH
[Off]
The projector can be operated without the PIN code.
Note
f
If you want to correct the digit, press the <MENU> button to reset the digit and then re-enter it.
f
Press the <ENTER> button after moving the cursor to [Cancel] to return the menu screen.
f
If you entered an incorrect digit, the digit (
) will turn red and reset, and then re-enter a digit.
[PIN code change]
Change the PIN code.
1)
Press
as
to select [Security].
2)
Press the <ENTER> button.
f
The [Security] screen is displayed.
3)
Press
as
to select [PIN code change].
4)
Press the <ENTER> button.
f
The [PIN code] input screen is displayed.
5)
Enter the PIN code you have set according to the steps in "Enter a PIN code".
6)
Press the <ENTER> button.
f
The [New PIN code] input screen is displayed.
7)
Enter the New PIN code according to the steps in "Enter a PIN code".
[Power management]
This function optimizes lamp power according to the operating status to reduce power consumption.
[Power management]
Set the operation as following if there is no signal input.
1)
Press
as
to select [Power management].
2)
Press the <ENTER> button.
f
The [Power management] screen is displayed.
3)
Press
as
to switch the item.
f
The items will switch each time you press the button.
[Ready]
The countdown timer is displayed after 30 seconds without input signal. The projection lamp turns off
and cools down when reaching the set time, meanwhile the projector will enter into the ready mode of
the power management. The projection lamp will be turned on if the input signal is reconnected or any
button (except for power button <
v
/
b
>) is pressed.
[Shut down]
The countdown timer is displayed after 30 seconds without input signal. The projection lamp is turned
off and cooled down when reached the set time, then the projector enter into standby status.
[Off]
Power management function is off.
[Timer]
Set the time that the Power management starts to work.
[Ready
Countdown]
The time from the state which the management function is working to the standby mode can be set to
0 ~ 30 minutes when [Power management] is set to [Ready]. The increment is 1 minute.
Setting [Timer] in step 3)
The time that the Power management starts to work can be set to 1-30 minutes. The increment is one minute.
1)
Press
as
to select [Timer].
2)
Press the <ENTER> button.
3)
Press
as
to switch the setting time.
f
The setting times will switch each time you press the button.
Setting [Ready Countdown] in step 3)
The time from the state which the management function is working to the standby mode can be set to 0 ~ 30 minutes when
[Power management] is set to [Ready]. The increment is one minute.
Chapter 4
Settings - [Expand] menu