Panasonic PT47WX53G PT4743G User Guide - Page 29

SET UP cont.

Get Panasonic PT47WX53G - 47inch PROJECTION TV PDF manuals and user guides View all Panasonic PT47WX53G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

SET UP (cont.) r CONVERGE (cont.) Note: After selecting, press VOL u to activate RESET TO DEFAULT feature. When using this feature in Zoom mode, the effect can only be verified when you exit all menus and display normal picture. IC ON MENUS OPERATION NINE POINT CONVERGENCE CORRECTION Note: Remote Control must be in TV mode. Procedure ACTION • Press to display red correction screen. • Press the 1 through 9 keypad buttons on the remote control to select the desired convergence position. • Use the navigation buttons to align the RED cross with the white cross pattern. Note: An adjusted cross pattern appears white with a minimum of color protrusion. CONVERGENCE ADJ. Procedure • After pressing VOL u the align Green to Center screen will be displayed. • Then use the navigation buttons on the remote control to align the horizontal and vertical green lines on screen, with the cabinet reference marks on top center and left center of cabinet, as shown below. Reference Marks • Press "0" on the remote control keypad to display the BLUE correction screen, then repeat procedure. Press "0" Front of cabinet ACTION • Press to display red center correction screen. • • Note: Use the navigation buttons on the remote control to align the red cross with the white cross pattern at the center of the screen. Note: To prevent picture tube damage do not leave test pattern on for an extended period of time. Then press "0" on the remote control keypad to display the BLUE center correction screen, repeat procedure for adjusting blue. If needed press "0" again to return to RED correction screen. An adjusted cross pattern appears white with a minimum of color protrusion. Press "0" • To exit press ACTION repeatedly, then press CH p. r OTHER ADJ. Highlight OTHER ADJ. and press VOL u to enter sub submenu field. Note: While sub sub-menu features are highlighted, press VOL u to adjust or activate. • MODE - To select TV (antenna) or CABLE mode depending on the signal source. • AUTO PROGRAM - To automatically program all channels with a signal. • MANUAL PROGRAM - To manually add or delete channels. • AUTO POWER ON - Select SET to power up the TV at the same time as the Cable box or other components or select OFF. • CHAN BANNER - Select ON to display onscreen banner when changing channels. • IMAGE SHIFT - Selecting ON is recommended for this feature to prevent image retention on screen. 27 l

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
I
C ON
M
ENUS
O
PERATION
27
l
SET UP (cont.)
r
CONVERGE (cont.)
Note:
After selecting, press
VOL
u
to activate
RESET TO
DEFAULT feature. When using this feature in Zoom
mode, the effect can only be verified when you exit all
menus and display normal picture.
CONVERGENCE ADJ.
Procedure
•
After pressing
VOL
u
the align Green to Center screen
will be displayed.
•
Then use the navigation buttons on the
remote control
to align the horizontal and vertical green lines on screen,
with the cabinet reference marks on top center and left
center of cabinet, as shown below.
•
Press
to display red center correction screen.
•
Use the navigation buttons on the remote control to align
the red cross with the white cross pattern at the center of
the screen.
Note:
To prevent picture tube damage do not leave
test pattern on for an extended period of time.
•
Then press “
0
” on the remote control keypad to display
the
BLUE
center correction screen, repeat procedure for
adjusting blue. If needed press “
0
” again to return to
RED
correction screen.
Note:
An adjusted cross pattern appears white with a minimum
of color protrusion.
NINE POINT CONVERGENCE CORRECTION
Note:
Remote Control must be in TV mode.
Procedure
•
Press
to display red correction screen.
•
Press the 1 through 9 keypad buttons on the remote
control to select the desired convergence position.
•
Use the navigation buttons to align the
RED
cross with
the white cross pattern.
Note:
An adjusted cross pattern appears white with a minimum
of color protrusion.
•
Press “
0
” on the remote control keypad to display the
BLUE
correction screen, then repeat procedure.
•
To exit press
repeatedly, then press
CH
p
.
r
OTHER ADJ.
Highlight OTHER ADJ. and press VOL
u
to enter sub sub-
menu field.
Note:
While sub sub-menu features are highlighted, press
VOL
u
to adjust or activate.
•
MODE - To select TV (antenna) or CABLE mode
depending on the signal source.
•
AUTO PROGRAM - To automatically program all
channels with a signal.
•
MANUAL PROGRAM - To manually add or delete
channels.
•
AUTO POWER ON - Select SET to power up the TV at
the same time as the Cable box or other components or
select OFF.
•
CHAN BANNER - Select ON to display onscreen banner
when changing channels.
•
IMAGE SHIFT - Selecting ON is recommended for this
feature to prevent image retention on screen.
Reference Marks
Front of cabinet
ACTION
Press
“0”
ACTION
Press
“0”
ACTION