Panasonic PTF100U PTF100NTU User Guide - Page 11

Cautions on use, Accessories, ENGLISH - 11 - pt f100u lcd projector

Get Panasonic PTF100U - LCD PROJECTOR PDF manuals and user guides View all Panasonic PTF100U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Important Information Precautions with regard to safety Cautions on use In order to get the best picture quality Draw curtains or blinds over any windows and turn off any lights near the screen to prevent outside light or light from indoor lamps from shining onto the screen. Do not touch the surfaces of the lens or the front glass with your bare hands. If the surface of the lens becomes dirty from fingerprints or anything else, this will be magnified and projected onto the screen. Moreover, when not using the projector, close the Front panel cover. Liquid crystal panel Do not project the same image for long periods of time, as this may remain as an afterimage on the liquid crystal panel. The liquid crystal panel of the projector is built with very high precision technology to provide fine picture details. Occasionally, a few stuck pixels may appear on the screen as fixed points of blue, green or red. It is recommended to switch off the projector once and try after 1hour later again. Please note that this does not affect the performance of your LCD. The projector has a high pressure mercury lamp and that is characterised as follows. The brightness of the lamp depends on the duration of use. The lamp may explode or shorten the lamp life by shocks or chipping damage. The lamp may explode only occasionally after using the projector. The lamp may explode if using the projector after the instructed lamp replacement timing. The lamp life is depends on individual lamp characteristics, usage condition and the installation environment. Especially the consecutive use of the projector for more than 10 hours, or the frequent switching on or off may greatly affect on the lamp life. Screen Do not apply any volatile substances which may cause discoloration to the screen, and do not let it become dirty or damaged. Optical components If you use the projector consecutively 6 hours every day, the optical components may need to be replaced in less than 1 year. Accessories Make sure the following accessories are provided with your projector. Remote control for PT-F100NTU*1 (x1) N2QAYB000152 Remote control for PT-F100U*2 (x1) N2QAYB000154 AAA batteries for Remote Safety cable (x1) control (x2) TTRA0141 Attachment screw (x1) Safety cable (x1) Mains lead (x1) K2CG3DH0053 CD-ROM*3 (x1) TQBH9009 *1. PT-F100NTU only *2. PT-F100U only *3. PT-F100NTU only ENGLISH - 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
Precautions with regard to safety
E
NGLISH - 11
Important
Information
In order to get the best picture quality
Draw curtains or blinds over any windows and turn off
any lights near the screen to prevent outside light or
light from indoor lamps from shining onto the screen.
Do not touch the surfaces of the lens or the front
glass with your bare hands.
If the surface of the lens becomes dirty from
fingerprints or anything else, this will be magnified
and projected onto the screen. Moreover, when not
using the projector, close the
Front panel cover
.
Liquid crystal panel
Do not project the same image for long periods of
time, as this may remain as an afterimage on the
liquid crystal panel.
The liquid crystal panel of the projector is built with
very high precision technology to provide fine picture
details. Occasionally, a few stuck pixels may appear
on the screen as fixed points of blue, green or red. It
is recommended to switch off the projector once and
try after 1hour later again. Please note that this does
not affect the performance of your LCD.
The projector has a high pressure mercury lamp and
that is characterised as follows.
The brightness of the lamp depends on the duration
of use.
The lamp may explode or shorten the lamp life by
shocks or chipping damage.
The lamp may explode only occasionally after using
the projector.
The lamp may explode if using the projector after the
instructed lamp replacement timing.
The lamp life is depends on individual lamp
characteristics, usage condition and the installation
environment. Especially the consecutive use of the
projector for more than 10 hours, or the frequent
switching on or off may greatly affect on the lamp life.
Screen
Do not apply any volatile substances which may
cause discoloration to the screen, and do not let it
become dirty or damaged.
Optical components
If you use the projector consecutively 6 hours every
day, the optical components may need to be replaced
in less than 1 year.
Make sure the following accessories are provided with your projector.
Cautions on use
Accessories
Remote control
for
PT-F100NTU
*1
(x1)
N2QAYB000152
*1.
PT-F100NTU only
Remote control
for
PT-F100U
*2
(x1)
N2QAYB000154
*2.
PT-F100U only
AAA batteries
for
Remote
control
(x2)
Safety cable
(x1)
TTRA0141
Attachment screw (x1)
Safety cable (x1)
Mains lead
(x1)
K2CG3DH0053
CD-ROM
*3
(x1)
TQBH9009
*3.
PT-F100NTU only