Panasonic PTLB90U Lcd Projector - Page 50

Maintenance

Get Panasonic PTLB90U - LCD PROJECTOR PDF manuals and user guides
UPC - 885170000070
View all Panasonic PTLB90U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Care and Replacement 5555 Attach the lamp unit cover and tighten the 2 lamp unit cover fixing screws securely with a Phillips-head screwdriver. 6666 Connect the power cord to a wall outlet. 7777 Press the POWER button and the projection starts. Remarks zzIf INITIAL START UP in the PROJECTOR SETUP menu is set to ON, the projector starts projecting when the power cord is connected to a wall outlet. (Æpage 39) 8888 Press the MENU button to display the main menu and press▲▼buttons to scroll to the PROJECTOR SETUP menu. 9999 Press the ENTER button to select the PROJECTOR SETUP menu and press▲▼buttons to select LAMP RUNTIME. 11111 Press and hold the ENTER button for approximately 3 seconds. zzThe LAMP RUNTIME confirmation screen is displayed. LAMP RUNTIME LAMP RUNTIME RESET. OK PRESS BUTTON CANCEL PRESS ANY OTHER BUTTON Note zzIf any button other than the POWER button is pressed, the LAMP RUNTIME screen disappears and the lamp runtime is not reset. (Repeat from step 8 again). 11111 Press the POWER button. zzAfter the lamp goes off, projection stops and the POWER button lights in red, then disconnect the power plug. 11111 The lamp runtime is reset to "0". Maintenance 50 - ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Care and Replacement
Maintenance
50 -
E
NGLISH
Attach the lamp unit cover and tighten the 2 lamp unit cover fixing screws securely
5 )
with a Phillips-head screwdriver.
Connect the power cord to a wall outlet.
6 )
Press the POWER button and the projection starts.
7 )
Remarks
If
z
INITIAL START UP
in the
PROJECTOR SETUP
menu is set to
ON
, the projector starts projecting when the
power cord is connected to a wall outlet. (
Æ
page 39)
Press the MENU button to display the main menu and press▲▼buttons to scroll to
8 )
the PROJECTOR SETUP menu.
Press the ENTER button to select the PROJECTOR SETUP menu and
9 )
press▲▼buttons to select LAMP RUNTIME.
Press and hold the ENTER button for approximately 3 seconds.
10 )
The
z
LAMP RUNTIME
confirmation screen is displayed.
LAMP RUNTIME
LAMP RUNTIME RESET.
OK
CANCEL
PRESS ANY OTHER BUTTON
PRESS
BUTTON
Note
If any button other than the
z
POWER
button is pressed, the
LAMP RUNTIME
screen disappears and the lamp
runtime is not reset. (Repeat from step 8 again).
Press the POWER button.
11 )
After the lamp goes off, projection stops and the
z
POWER
button lights in red, then disconnect the power
plug.
The lamp runtime is reset to “0”.
12 )